eachine whoop 3d models
5549 3d models found related to eachine whoop.thingiverse
This is a eachine e010 base to reinforce the whooper. The distance between the rotors is 47mm. ...I made this base because of the ones that I found are too short and create a bend.
thingiverse
I had trouble getting a good fit with the original model. It was too loose for the Racedayquads 250mAH "HV" Batts that I run. I measured a battery and drew my own version of this from scratch with inspiration from the original. This has a nice...
thingiverse
Camera holder for E010s, holds camera at 20 degrees and protects it. front tabs hook around the PCB. I added a tiny zip tie on top to streamline the top edge and protect the antenna. fits the stock e010s camera and pcb. weighs in around 1 gram. ...will...
prusaprinters
<p>I had trouble getting a good fit with the original model. It was too loose for the Racedayquads 250mAH "HV" Batts that I run. I measured a battery and drew my own version of this from scratch with inspiration from the original. This has a nice...
thingiverse
Replacement for your origianl Frame. ... M2 Spacers are necessary:...
thingiverse
Chasis para Eachine E010 mas ligero y rápido. ...Tamaño original.
thingiverse
Eachine TX05 Tiny Whoop mounts with different options: - Tilt from 0° to 35° - low (4mmm) or high (14mm) - optional tab for an RX weights depending on options from 0.4g to 1g
thingiverse
Eachine TX03 mounts for the Tiny Whoop - 4 different angles - 0° 10° 20° and 25° These are yet to be tested so YMMV :) Update - the 0° mount has been edited to correct the base thickness
thingiverse
A case to hold the Eachine E10S micro FPV quad and up to 16 batteries! ... Inspired by the original Tiny Whoop case seen here: https://www.thingiverse.com/thing:1580567 (assuming that was the 1st one, there are many)
thingiverse
The shims are now attached to the baseplate to raise the cameraholder 2 mm above the circuitboard of the Tiny Whoop. Also added some support to the part that actually holds the camera just to give it some extra ruggedness. The screwholes are...
thingiverse
Whoop/Toothpick mount for the eachine tx06 aio cam Around 2.5 grams with 30% infill
thingiverse
This is a box for Eachine E010 or Tiny Whoop with a FPV antenna. ... U can store extra motors in the corner of the box and there is a insert for batteries, loader, propellers or other stuff that fits into the box.
myminifactory
This upgrade kit helps you transform Eachine E010 into a Tiny Whoop, https://www.tinywhoop.com, by bracing the frame and attaching a video camera! I have focused on making a kit for the absolute beginner rather than the expert flyer. So the; frame...
thingiverse
This is a camera mount for the FPV AIO camera vtx combo here: http://amzn.to/2jvJupE This will NOT fit the larger Eachine TX-01/TX-02/TX-03 The mount is attached directly to the Flight Controller board with VHB.
thingiverse
This is a model of the hood for the Eachine E013 or like frames with a camera. I have added the 3rd hole on the front right of the hood for the receiver antenna to come through. This hole allows for a range boost on the drone. Final weight is around...
prusaprinters
This is a model of the hood for the Eachine E013 or like frames with a camera. I have added the 3rd hole on the front right of the hood for the receiver antenna to come through. This hole allows for a range boost on the drone. Final weight is around...
cults3d
30% Lighter Better fit Fits most of Eachine E010 and E011 style quadcopters - check tags For Tiny Whoop / Newbee drone / GNB whoop batteries - 3.7V / 4.35V Only thing you need to do is cut end of the battery holder to fit it trough
thingiverse
- 30% Lighter - Better fit - Fits most of Eachine E010 and E011 style quadcopters - check tags - For Tiny Whoop / Newbee drone / GNB whoop batteries - 3.7V / 4.35V - Only thing you need to do is cut end of the battery holder to fit it trough
thingiverse
This is a tiny, lightweight and fast to print protection for a camera on a Tiny Whoop frames. ...It clamps right and left at the original pints on the Frame.
thingiverse
Features: - Lightweight (single 0.5mm wall) - 100% Camera protection - Bottom skirt to prevent dirt entering your electronic - Smooth design (no fancy fins that bricks aerodynamics)
thingiverse
printed with TPU. ...mount for the Eachine tx02 for a tinyh whoop. ...This mount has no up tilt.
thingiverse
Mount specifically designed for the Eachine EF-01 micro camera + VTX for the Furious FPV Acro Whoop flight controller. ...Designed by @EAM5892.
thingiverse
A fun project. Print it, fly it, any material is good.... Print upside down with supports that make sense to you. Also added a thinner 1mm version, should be... well half the weight give or take.. BTW, hold battery on with rubber band. Note: V4...
thingiverse
CAmera mount for my Eachine TX01 fpv camera - tiny whoop
thingiverse
Mount for the Eachine TX04 AIO camera for the Inductrix / Tiny Whoop frames. ...I'm using it on a cockroach frame from NewBeeDrone.
thingiverse
Usage Print 2 of them for each stick Use a zip tie to hold them together Here is my tutorial how to turn the Eachine E010 into a Tiny Whoop:https://oscarliang.com/eachine-e010-tiny-whoop-inductrix/ For more awesome E010 Modifications, check out this...
thingiverse
This canopy works with e011 frame or 65mm frame even 75mm
prusaprinters
Mount for the Eachine TX04 AIO camera for the Inductrix / Tiny Whoop frames. I'm using it on a cockroach frame from NewBeeDrone.</p> <p>Use a bit of hot glue to keep the camera in.</p> <p>.f3d file is on Thingiverse because PrusaPrinters doesn't...