eachine wizard x220 3d models

I modified the mounting holes to match eachine wizard specifications\n4. A hole on the bottom reduces weight and improves stability\n5. I added a numerical indicator for the uptilt angle\n6. ...Support was added to the top back corner to prevent...

Gopro8 mount 25° for Eachine Wizard X220HV available with and without immortal T mount The design includes full access to battery, buttons and as much as possible to back screen. The design is based on 6mm hollow bumper all arround the gopro, and...

This is the inaugural release of the Navaho Wizard shell, engineered to accommodate a more substantial RX while incorporating an underslung battery design for added sleekness. ...Crafted with Taulman's T-Glase material, this prototype boasts exceptional...

This is a revision on my DJI retrofit for the Wizard 220HV frame. This revision assumes you are using the provided 20mm standoffs and is less bulky than the previous design. The included camera mount is a fixed 36 degrees. Sorry if that's not what...

The Eachine Wizard X220 features seamless integration with the Nilox Mini WiFi Camera, allowing users to effortlessly stream live video feed from their drone directly to their smartphone or tablet via a stable and secure internet connection.

If I can't print this, please consider ordering it through my 3DHub at: http://3dhubs.com/service/8Bit The original was slightly too long. See the link here with the picture to see the difference in lengths for the holes. ...https://imgur.com/a/jOoHz ...

<p><strong>Minimalistic ESC Cover for your FPV Quad</strong></p> <p>Print time is about 4 minutes.</p> <p>I've designed a minimalistic solution to<strong>keep the ESC's of your FPV Quad save from your props in a crash</strong>. ...The slits on the top...

This bracket is specifically designed to seamlessly integrate with the authentic GoPro clip mount.

If you can't print this model yourself, order it directly through my 3D hub located here: http://3dhubs.com/service/8Bit. The original design was slightly too long; check out the link to see a comparison photo of the adjusted holes. ... If you're going...

Crashed parts are too flimsy. Every time the quad crashes on its back, the battery plate is shattered. So I decided to separate it into two parts so that the rear section can be close to the FC stack. As a result, when it crashes on its back, the...

Print on TPU at 100% infill, utilizing washers and orienting the model sideways.

Cut to the chase, tear it apart, display it.

Minimalist ESC Cover for Your FPV Quad Print time is approximately four minutes. I've crafted a minimalist solution to safeguard your FPV quad's ESCs from damage in the event of a crash. The slits on top will likely aid in keeping the ESCs cool...

The antenna holder secures the antenna horizontally, safeguarding the frame from harm at the original antenna mounting point, while also preventing the antenna's flexibility, which reduces wear and tear over time.

Hi, this is my original project for Eachine Wizzard X220 V2 (but it will also suit to many other 5" quad drones). It's size is designed for typical antennas and Beitian GPS BN-880Q with compass. Print it in slow motion with 100% infill for better...

... angle of 45 degrees, all integrated into one convenient unit. ...I've successfully implemented this design in my Eachine x220, with everything functioning smoothly as expected. ...Feel free to give it a try and experience the benefits for yourself.

This revised version is designed to optimize the mounting system, ensuring easier zip tie installation and enhanced printability. The design has been crafted using Tinkercad, a powerful online platform that allows for seamless editing and refinement...

I rely on this versatile tool to secure both antennas under the sturdy quad, a testament to its ability to withstand rough landings time and again. ...Print Options Include: Supported Features: Absolutely Anything Goes Infill Settings: Optimized for...

good quality is in PETG full filling on Ender 3 is 1 hour and 7 min. ...happy flight

It's a straightforward sketch devoid of any curved lines yet it gets the job done effectively.

I attached a sturdy side plate to the device, carefully crafting an additional millionth of an inch to reinforce its central core. ...Without this added stability, the entire assembly felt fragile and prone to collapse.

This is a CommDock designed originally for the Wizard X220, but it fits the Martian 2 or any other similar x220 size frame with similar widths - there are a few. This is my first release of the design. I've held onto this design for about 3-4...

Mounting this camera is a breeze, allowing for precise positioning on top of the Eachine Wizard X220s. To ensure stability, secure it firmly with a strap directly onto the mount. ...The recommended camera angle is 30 degrees.

These are standard footings for the Eachine Wizard X220S quadcopter. ...To assemble it correctly, you'll require longer M3 screws measuring 9 millimeters, as opposed to the shorter ones that come with the drone at 6 millimeters.

This mount secures a BN-180 GPS to the back of an Eachine Wizard. Printed from TPU, it has endured multiple crashes without issue. ...Onlookers consistently compliment its sleek design.

Moved to: https://www.prusaprinters.org/prints/100027-eachine-wizard-x220s-gopro-hero-567-mount Full Protection, 10, 15, 20 and 25deg angles. ... Print in TPU for more durability and PETG for more cam protection (but will break while crashing) Use...

VTX Mount for Eachine Wizard X220s Quad Copter The stock VTX mount is extremely delicate and shatters upon a crash, additionally damaging the antenna as it takes the initial impact of the collision. Consequently, this VTX mount was designed to...

A Hero Mount for the wizard x140hv

Crafted to connect SMA plugs securely. The VTX and Rx combo functions perfectly on the modified top plate, which features a new mounting system created by removing the outdated holder. ...Please note that these designs are specifically suited for 30mm...