eaglemoss replacement stand 3d models

Replacement handle for Wolfcraft "Single Roller Support Stand" purchased from Canadian Tire, designed to support the end of lumber during cutting operations. The manufacturer's lever-type handles on both of my units broke; these replacement handles...

These replacements have held up remarkably better. It should be an effortless print and replacement for anyone in need of one. Simply drill out the rivet and install a bolt and nylon locknut. You can opt to use supports just for the through hole if...

STL files to replace a missing doll stand on the 2016 collector Skelita doll. I did my best to get a good amount of detail and maintain the files as light as possible. -The fitting between the pole and base is modified to allow for easier assembly...

To cater to my chickens' hydration needs, I assembled a water stand from similar components as my printed one. However, the original part broke, so I fabricated a stronger replacement. This new part was constructed using a MakerBot 2 printer with 10%...

I lost one of the clips for the stand, so here's the clip I created to replace it. ... ...

replacement clip for virtual boy

Replacement Part for Umbrella Stand which holds umbrella by screwing a plastic part down and compressing it against the pole of the umbrella. The original part broke (last picture) and after not being able to find a suitable replacement i decided to...

Inside the Philips Stand mixers HR1565/55 and comparable models, a multitude of plastic gears work in tandem to rotate the bowl using the mixer's rotational motion. When two of these essential gears failed, I took on the challenge of designing...

... metal ring so that I could remove it from the old base and transfer it to the new 3d printed one. It's slightly smaller than the original. This one is 140mmx150mm If there is a need in the future, I will create a replacement top tray as well. ...

Unfortunately, it wasn't properly seated,  so the cover got locked in the wrong position.The case comes with a stand tool, but I had misplaced mine, so I designed this 3D printable replacement instead.I printed mine in PETG, but you can print in...

After loosing one of the plastic feet of my Willworx MTB stand,  i made my own and slapped together a set of replacement feet for it. If you print it at 100%, it will perfectly fit, BUT it won' sit snug on it and you would need to glue it somehow.

Replacement case stand for A50 phone model Latest version: 3 how I installed: 1. put the metal pin in the hole to connect both pieces 2. sweep the part at an angle into the upper case slides with the upper part 3. ...to install the bottom part (has...

I created this part to replace the damaged original. ...Follows the original file for editing in fusion 360.

Replacement foot for my child's Time Timer 12" clock. ...The original foot was brittle and broke.

Thank you!** DESCRIPTION A replacement part for the commonly missing Imperial Speeder Bike flight stand. <h3>FILE DESIGN & DETAILS</h3> <ul> <li>Dimensioned using the actual part for reference. </li> <li>It is manifold and has been checked for...

I misplaced a foot on my C-Stand during a studio shoot, resulting in scratched floors and uneven stands. ...To rectify this issue immediately, I designed and printed a new one overnight.

Replacement Feet for Classic Rummikub Game. ...Be Sure to Verify Compatibility Before Printing to Ensure a Perfect Match for Your Existing Set.

I'm using a custom-made replacement part for my replica Otterbox case, which broke down on me. ...To fix it, I designed and manufactured a new one myself from high-quality ABS plastic, and now it's functioning perfectly.

I tightened the assembly for holding my microphone's legs to the stand too much, causing it to crack around the screw hole. This made the lower part of the stand loose, so it would spin whenever I picked up the mic. I designed a new part based on...

Originally by JackMapo. ...I lopped off one of the bottom rings and shrunk the peg. The first time I printed the stand, the peg was too large. ...I feel it was likely due to the tolerances on my machine.

I quickly dismantled the worn-out speaker stands and set out to craft a pair of sturdy new knobs, transforming a necessity into a fully functional reality within just two hours, a true testament to my resourcefulness.

This custom OpenSCAD script serves as an expedient fix for a faulty component within a Christmas tree stand. ...Feel free to adopt and modify this code to suit your specific requirements.

A replacement part for my Cherry KC 1000 keyboard. Works great, maybe print a tiny bit wider to make the clip-in mechanism a bit more snappy. ... Built in tinkercad, sliced with Cura at 0.12 mmm resolution (should also work with .18 or even .2)

Which is why I did my best to create a replacement! Maybe it will work for other models, but I'm not sure. Check the dimensions! It doesn't have that satisfying snap when closing but the fit is quite snug and has good tension. ...Hopefully it will...

I use my music stand, which I'm not sure if the standard size fits it perfectly, but it does fit snugly and required a lot of force to get on. You might need a rubber mallet to tap it into place. It would be ideal if it was printed with a flexible...

... pieces, you'll be able to enhance your gameplay experience like never before. But wait, there's more! I've also created an innovative stand that takes Rummikub to the next level. ...Check it out here: https://www.thingiverse.com/thing:3384783

This is a replacement "clip" for the inside of a Cisco 7970 (and any model with the same case). As you can see in the image, the original clip disintegrated so I decided to model it in Fusion 360 and print it. There are two versions available. The...

This is a replacement "clip" for the inside of a Cisco 7970 (and any model with the same case). As you can see in the image the original clip disintegrated so I decided to model is in Fusion 360 and print it. There are two versions. The SIMPLE one is...

We're working with one-quarter inch thick wood stand-ups.

The replacement plate designed specifically for the Eaglemoss 1/8th scale DeLorean model is now available. ...This part replaces the original circuit board and is compatible with the RobotDyn Mega 2560 Pro microcontroller.