early bronco bumpers 3d models
26414 3d models found related to early bronco bumpers.thingiverse
A bracket to put a 4 in speaker in early bronco in original speaker slot.
cults3d
Bumpers for TRX-4 Bronco. ... 2 versions of front bumper - one of them is designed for TRA8088 light Rear bumper has better coverage of lexan body
thingiverse
A cup holder designed to fit in between the front two seats of a 72 bronco. a slot to fit a 4 inch speaker and room to rout cables. ...two slots are implanted to place phones in the cup-holder.
grabcad
Bronco column cover files for 3D printing. Model has an extra cut out above steering column for aftermarket gauge wiring passage. ...I also included a standard version without the wire passage.
thingiverse
2020 Bronco? Tried to make as much printable as I could. You could put the body on something else or put a different body on the chassis. Probability a few parts missing. If a part is missing or wrong ask, I'll have it somewhere. Diffs ...
thingiverse
I made these seat backs for when you flip the seat to fit a 6" driver. Flipping the seat makes the driver fit better but leaves the back open. ...I gave it a quick sand with 400 grit and painted it Semi Gloss Black Tamiya TS-29.
thingiverse
Bumper replacment for scx-24 Bronco, remove stock bumper and mount, this replaces the whole setup Print flat with no support
thingiverse
This is a replacement front bumper support for the scx24 bronco. ...Removes the gap between body and bumper without raising the body post.
thingiverse
i designed this sport bumper for the bronco to make it more sport looking but still mantaining some scale look, i also made hole for the bumper lights and a hole for the winch, it is fitting perfect on the stock bumper moun and is not going to bind...
thingiverse
I made this bumper to fit my Traxxas TRX4 Bronco. It fits nicely and has a few holes for mounting. I am planing on making mounts for lights. I think a KC style light would be awesome. I printed this out with Inland White PETG and it is pretty strong....
thingiverse
ditch the bumpers and clean up the look. ... will need to scale up 10 times for correct size. front bumper delete - 28.726mm x 34.534mm x 12.7mm rear bumper delete - 22.86mm x 38.608mm x 5.588mm print at 100 for strength
myminifactory
The TRX4 Bronco Bumpers are a direct fit for the Traxxas TRX-4 Bronco. these bumper gives improved clearance and the ability to mount up to 4 external spotlights (sold seperately). The design also has a built in fairlead for those with a chassis...
cults3d
SCX24 Bronco High Clearance Bumper designed so the wheels will not rub and gives awesome approach angle. ... The body standoff is set to lowest position.
cults3d
A custom built sleek and much more tucked SCX24 Bronco front hoop bumper. 3D printed and maintains the factory fog lights, just relocated to a more central fog light position. ...This bumper allows for better approach angles and does not interfere with...
grabcad
These designs aren't complete yet, but they were some ideas I was working on. ...They were for my 1969 Ford Bronco. Front bumpers. ...Models are in 2014 SolidWorks.
thingiverse
This is a big stinger bumper for the TRX4M Bronco. 3 M3x10mm screws needed to bolt together. Print at 100 for plenty of strength to lift the car itself. Might need to change the scale to times 10 for right size. bumper should be 28.726mm x 48.768mm x...
thingiverse
This is a set of mounts, to bring the front bumper in and up to the body. ...It is in 2 pieces and replaces all the factory mounts, because the factory mount hits the servo at this location.
myminifactory
this V1 of the TWSD Bronco tube bumper. ...This bumper is a direct bolton no modification required.