easy cable 3d models

Very easy to manufacture cable channel. Instructions ABS plastic is used 3 or 1.75 mm. 6mm or 8mm stud. Two nuts and washers, drill. ...I used cable_clip_13mm.stl channel 6mm stud and 1.75mm And...

Yet another cable strap to make with flexible filaments. ...

English: An easy to use cable clip. Just attach it somewhere with double-sided tape. This is my first creation, so be kindly ;) I will improve it soon. Deutsch: Ein einfacher Kabelclip. Einfach mit Doppelklebeband überall zu befestigen. Ist die...

... double sided tape, or screws for a permanent fixture. ... -Fits up to 4 cables, max 7mm diameter -Screw mount with 2x M4 or similar countersunk screws -Screws are 15mm apart This part was designed to keep my audio interface cables clipped out of sight

Clips wires together to hold them all straight, I used them for monitor cables and they are designed to hold 6mm thick cables, but could easily be scaled. I have includes models to hold 2-6 cables and one that holds 6 in a 2x3 arrangement. ...If you...

Easy wire management, clip on, clip off. ... You can use screw or attach it with double sided tape

This cable management clip holds cables securely in place, yet lets you easily add or remove cables when needed. It was inspired by a clip I used on the job years ago. Nobody knew who made them yet everyone wanted them, so I went ahead and...

Small will hold 2 cat6 cables or several smaller wires, small/tall is good for 3 cat6 cables and for bunching extra wire from a/c adapters. OpenSCAD source is included so you can customize to your heart's content. If you customize, I recommend...

I designed this cable clip in OnShape based on a .28mm resolution with a 20% infill. I had trouble removing some old ones from my Ender 3 and designed this one with a lip to be able to make removal easier. ...You can duplicate a few of them before...

The rings can be used for cables that shouldn't be held down by ties, just expand the gap and slide your cables in. Small rings are aprox. 15mm in diameter and the large is aprox. 26mm in diameter. The large ring is should work well for the hotend...

So I decided to make a simple cover to hide all those ugly cables in the rear right corner Easy to mount with 2-3 short M3s and printed T-nuts I printed mine split in two because I didn´t have time to print it all at once. However as a bonus i...

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

A quick-and-dirty remix of the Ticwatch S/E Dock by Vitting, in order to widen the channel the cable gets inserted through. I travel a lot, and so end up adding and removing my cable a lot. ...This should be a much easier variant to do that with!

This kind of stuff, is provided with a second thing to protect cables from water and rain, when user removed his GPS from is dongle. ****Français**** Ces items permettent de connecter les câbles d'un GPS Garmin et simplifier le montage. Il...

<p>Customized version of <a href="https://www.thingiverse.com/thing:2596197">https://www.thingiverse.com/thing:2596197</a></p> <p>Created with Customizer! ...<a...

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Wrap your cable in this. ...Super simple.

1.Choose Cable_clip size according to table thickness Recommend print settings: For Cable_clip INFILL=0%, Plate Adhesion=ON, Wall line count=4 (for better spring effect) For Cable_holder INFILL=30%, Plate Adhesion=OFF

Printable cable management for your desk!It can be printed in the length you need it!Models to print:top and bottom of the chainoptional: the small framework for adding additional weight to the chainthe chain links. I needed 38 pcs for the one in the...

1) Needed to be small this one can do 180 degree turn using 5 links with a total width of 45mm 2) Cables enclosed as possible this ones max gap is under 5mm 3) Easy to print I print mine with no supports Dimensions 14mm High x 24mm long 18mm Deep...

1) Needed to be small this one can do 180 degree turn using 5 links with a total width of 45mm 2) Cables enclosed as possible this ones max gap is under 5mm 3) Easy to print I print mine with no supports Dimensions 14mm High x 24mm long 18mm Deep...

Simple cable chain for laser engravers etc... 10mm x 6mm inside the smallest links, 15mm centers for all links. ...(Closed links, no removable retaining piece.) I will be adding the mounting pieces once i get to them.

Why go for complicated "drag chain" - use simple principle KISS Cable management using retractable key chains - get them at a budget stationer outlet https://www.youtube.com/watch?v=aoZX6ms_loo Print with no supports Once I figure out why Fusion360...

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197

Customized version of https://www.thingiverse.com/thing:2596197 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2596197