easy flyback 3d models
206319 3d models found related to easy flyback.thingiverse
Instructions Find an old CRT television (An old television mainly used during 1990s or later, these are the televisions that were large and are pretty common to find.), these contain a component called a Flyback Transformer, google to make sure what...
cults3d
This is an easy to make project for a High voltage power source. "HIGH VOLTAGE GUNS, MORE DEAD PEOPLE AND MORE HIGH VOLTAGE FUN" Make sure to check out the instructions. Be careful while handling high voltages, this has enough energy to stop someones...
thingiverse
A quick and easy segmented flyback secondary for a rectangle type ferrite core. The core is from Ali-x and is named "UF86A Ultra Large watt isolator". The segments are 3mm wide with a 3mm wall. ...
grabcad
3D model of the Flyback Transformer and its core size is EE-16. ...This model was created using FreeCAD that original model file is also included.
thingiverse
For anyone who is doing maintenance on an old CRT G07 Monitor and replacing the Flyback, sometimes you need to bend the pins to get it to drop into the board easier. This is very hard through trial and error with the actual PCB so I made this...
thingiverse
A 3d printed multi section bobbin for flyback transformers for small ferrite transformer cores. Print sideways and put support blocker in the middle. It will print fine without support in the middle. ...KEEP SUPPORT ON FOR THE BOTTOM.
thingiverse
FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : And (Another) Another Spool-Holder [0] Thing URL : http://www.thingiverse.com/thing:32391 [0] Thing Author : pgreenland [0] Thing Licence :...
thingiverse
This is a simple little box that holds a flyback diode for solenoid flyback protection in my virtual pinball cabinet: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/ The diode is needed to 'short circuit' any current caused by the shaft...
prusaprinters
This is a simple little box that holds a flyback diode for solenoid flyback protection in my virtual pinball cabinet: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/ The diode is needed to 'short circuit' any current caused by the shaft...
thingiverse
30 ga wire primary is 10.5 ohms 101.74 feet secondary is 72.4 ohms 701.55 feet C1 is 76.1 ohms 737.4 feet C2 is 70.1 679.26 feet all will fit on the spools Instructions this is part of my research on pulsing core transformers this is a cheap TV...
grabcad
Features:Core Type: EF16Maximum Output Power: 16WPrimary / Secondary Insulation – 4000VrmsPrimary / Secondary Creepage – 6mm min.Triple insulated wire is used to provide reinforced insulation between windingsInsulation Material Class F...
thingiverse
A simple mount for a Flyback Transformer found on ali express or ebay etc. These things can be used for a marx generator or other fun stuff You can just use superglue to place the mount on a flat surface or use screws there are two m5 screw...
thingiverse
This winding body is for building a working flyback transformer that lasts very long and can output a whole lot of power with the right driver. Please only build this if you know what you are doing. I take no responsibility vor any injuries or...
grabcad
I made these bobbins for a set of old used U cores I bought off of Ebay. They are a little shorter than Stan's original flat U cores, so I left out one small coil in one of the bobbins. ... Dimensions of the ferrite U core: Diameter: 16mm Inside length...
thingiverse
This is a very simple shroud designed to fit over the top of the large red glass high-voltage resistor that Sony uses in its PVM line of CRT monitors. I had a crack in mine that caused an arc to jump to a nearby grounding tab on the inside of the...
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Customized version of http://www.thingiverse.com/thing:305087 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=305087 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1399029 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1399029 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:753477 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=753477
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130