easythreed x1 firmware 3d models

I have created an open case for my Kaiser Baas X1 Action Camera. As I would like to be able to charge my camera while using it. Sometimes you need to take timelapse's that could take hours to complete and the battery does not last that long. In the...

I've designed an open case for my Kaiser Baas X1 Action Camera that allows me to charge it while using it. Sometimes, taking timelapses can take hours and the battery doesn't last long enough. In the standard case, I couldn't access some buttons,...

This is my remix of the popular two-piece flat clamp for the extruder cable. I did it mainly because I personally didn't like the fact that the clamp bar has the holes open, so I designed this which is equivalent in its function, but it doesn't fall...

This is a Z-axis mount specifically designed for the sidewinder X1 printer. It securely holds the Vitade HD960 webcam in place, which features an integrated ring light that provides essential illumination on the print bed. I opted for this camera...

A dampener I designed for the Artillery/Evnovo Sidewinder X1 that uses a squash ball to reduce vibrations. I have impressive results with this setup and modest speed, jerk, and acceleration, allowing me to print small zig-zags without affecting...

... ! (attention à mettre des supports jusqu'à 50° pour éviter les défauts au niveau du décalage en z) Print Settings Printer: Sidewinder X1 Rafts: No Supports: Yes Resolution: 0.2 Infill: 10 Filament: Eryone TPU Black Category: 3D Printer Accessories

Parts to be printed to offset and protect the cable from the tray of the Artillery Sidewinder X1 3D printer. The machine is freed from the constraint of leaving space behind for the mobility of the cable (quite fragile, the silicone and fiberglass...

I have created this sensor holder to remove the original spool holder from the top of the Artillery Sidewinder X1 printer and use a filament drying box. This sensor holder is very compact and makes the printer lower than in the original...

If you want to purchase the fan I leave the video where he explains improvements and directs you to the store.https://www.youtube.com/watch?v=lBemrqoUbdc&t=15s-------------------------------------------------------------------Esta es una montura...

The Bambu Lab X1 & X1 Carbon use a PTFE bowden tube to guide filament to the print head. There is a little bit of wiggle, which causes the tube coupler to dig into the tube over time. I was never very happy with the amount of play allowed and...

Here’s my take on adding extra light to the chamber.  Hat tip to Francis Marasigan for first showing the benefits of adding extra light! As mentioned by others, best to turn the light off until after the first layer inspection as the light...

It was a very good idea to design it removable because I realized later that the Sidewinder X1 detector was not compatible with my octoprint :( But anyway. It might be useful to someone else.</p> <p>After that, I tried two-color printing and found it...

The Bambu Lab X1 &amp; X1 Carbon use a PTFE bowden tube to guide filament to the print head. There is a little bit of wiggle, which causes the tube coupler to dig into the tube over time. I was never very happy with the amount of play allowed and...

A dampener I made for the Artillery/Evnovo Sidewinder X1 that uses a squash ball to dampen the vibrations. I have great results with this and modest speed, jerk and acceleration, it allows me to print small zig-zags without it affecting the surface...

Also the "cheap" chinese linear rails (MGN12H) are a bit louder than V-rollers, but not much. Have fun with this modification. You need this: 1x M3x20mm 8x T-nut 8x M3x8mm 8x M3x6mm 2x M3 Nut 4x M3x30mm (with heads cut of) 1x Bohrplatte.stl 2x...

The top lid is intended to be used when the vat is inside the printer, featuring cutouts on the sides that perfectly accommodate the X1 hold down brackets. The top cover boasts a light-safe design, making it ideal for covering the vat during...

This is a set of lids, bottoms, and resting trays for the Epax X1 resin printer. The interior top lid is for use when the vat is in the printer. It has cutouts on the side for the X1 hold down brackets. The top cover has a light safe design. It is...

washers [UPDATE: A user stated out in the comments, that in the newer versions of the X1 something has changed and M3x20 + washers have to be used; check it out!] (but without screwing them tight yet). Then adjust the position of the strain relief to...

... To make things easier, I used Repetierhost to update the firmware settings without any hassle. ...However, keep in mind that you'll also need a different coupler for the stepper motor - specifically one that converts an 8mm to 5mm connection.

I pretty much only use Overture and was bummed when I got the Carbon X1 and you can't use the cardboard spools with the AMS feature. There are several other spool holders out there but I had issues with them for various reason. The tape coming off...

If you use the AMS with the 3D version, do so at your own risk, you are literally living on the edge and it may fall off.Print 1 or 2 dogbone joiner pieces - they are slightly tapered and you may need some finessing if you haven't done any additional...

Hi friends I don't know about you but I don't like opening my Artillery SideWInder X1 when I want to flash it.I know that some successfully tried to use the "About" screen to flash directly. But on my machine it didn't work. I also know that there...

I Use a Sidewinder X1 but Most Settings Should Work on a Genius and Many Settings Should Also Work for Other Printers. German: I've Been Active in the Drucktipps3D.de Forum for Some Time, Helping Newbies Especially. Here Are My Cura Settings as a...

Experience top-notch modeling with the 'Hx X1 High red' designed specifically for your projects. This precise and realistic model allows you to utilize it across various projects effortlessly, as it adheres to correct proportions and actual size. The...

Thing Details: Updated extruder lever arm designed specifically for Artillery Sidewinder X1. Main changes include: 1) Dual bearings run on motor shaft, stabilizing the arm and reducing wobble. 2) Bearings spaced to align feed tube with hotend...

Very easy to attach or detach. Print Settings Printer: Artillery Sidewinder X1 Rafts: No Supports: No Resolution: 0.28 Infill: 15% Notes: Material doesn't matter, but the matte black I used is pretty slick looking. Post-Printing =============...

Filament Spool Holder for Zaxe X1/X2/Z3 3D Printers Instructions: Place the model in your slicer as in the picture Take your print from the bed and rotate it 90 degrees on the Y-axis Insert it through the opening at the back of the Zaxe printer...

I'd like to hear your thoughts on a custom GoPro mount designed specifically for the JJRC X1 Quadrocopter! This mod allows you to attach any camera of your choice to this versatile drone. To get started, remove the original feet from the quadcopter...

This is my version of a gantry support for Artillery Sidewinder X1 V4. To assemble it, you will need: - 8 M5x16 screws - 2 M3x40 screws - 2 M8 threaded rods (lenght 730 mm) - 10 M8 nuts Instructions: - Fix Part A on the top of the gantry...

... you can find online that fixes the auto-focus for the close up distance. Print Settings Printer: Artillery Sidewinder X1 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 20% Filament: Longer PLA Black Category: 3D Printer Parts