ec5 to traxxas 3d models
2133220 3d models found related to ec5 to traxxas.thingiverse
Traxxas Unlimited Desert Racer battery plug mount to replace the Traxxas plug mounts with EC5 plug mounts. Print two of the upper plug supports and one lower plug support. ... Printing: Line Width: 0.4 mm Line Height: 0.2 mm Material: PLA ...
thingiverse
This is a simple and clean design that let's you take out the IEC connector for an AC input and replace it with this adapter to let you take a regular EC5 connector for hobby batteries and glue the connector in this adapter (As shown in the pictures)...
cults3d
This is a protective cap for Lipo or other batteries with EC5 connectors. This cap eliminates any risk of short circuiting when storing your batteries. ... Also available for Dean and XT60 sockets.
thingiverse
I have been traveling on the airlines with lipo lately and decided that I wanted to make TSA a little happier by covering the battery plugs. I have made these with the green in the pic as well as some magenta. I will use the magenta caps if the...
thingiverse
... ... The `Base` component fits inside the holes in the EC5 housing allowing the pins to be pressed in-place using the `Press` component to push or hammer the top of the EC5 housing, moving the wires to the side and increasing the top surface area.
thingiverse
I've standardized to EC5 on all my R/C aircraft (Fixed-Wing, Helis, Multicopters) and just got tired of busted fingers using violent means of disassembling EC5 connectors. This is a really easy and positive way to remove the bullets and cups from EC5...
prusaprinters
A cap for EC5 connectors on batteries. ...I use it to mark batteries that have been charged as well as further protect from accidental shorts.
thingiverse
I found that the contacts within the EC5 connector are a bit to exposed for any loose metal lying around. I feel more comfortable carrying these batteries around in a lipo-safe bag using a cap over the connector. ... ...
thingiverse
... and grip respectively. The middle surround was then extruded by 16.5mm for the connector and 2mm to clear the base/grip. I chamfered the inner edges to aid fitting the EC5 in, and rounded some of the external corners to improve strength and comfort.
thingiverse
This is a EC5 holder for the Tron 5.8 No support needed for the holder. ... 2x M3x12mm Screws are needed to clamp the 2 parts around the connector. ...They can directly screw into the plastic without any pre-preparation, no Loctite or glue needed.
thingiverse
Panel mount EC5 connector. ...Simply glue the contacts in place after soldering.
thingiverse
To put 1/8 scale traxxas rims on a 12mm hub. ...printed and works.
myminifactory
Stable stand for Traxxas TRX6 Mercedes-Benz G63 6x6. Splitted into 12/20 parts - easy to print. ... UPDATE: 20 part version for print on 200x200 bed
thingiverse
Stable stand for Traxxas TRX6 Mercedes-Benz G63 6x6. Splitted into 12/20 parts - easy to print. ... UPDATE: 20 part version for print on 200x200 bed
pinshape
Created by us folks at elequa, it's purpose is to hold electrodes suspended in a water sample to be treated with EC, a process which can do amazing things like clarify fracking water, kill bacteria and viruses, and even turn soda pop back into...
thingiverse
Created by us folks at elequa, it's purpose is to hold electrodes suspended in a water sample to be treated with EC, a process which can do amazing things like clarify fracking water, kill bacteria and viruses, and even turn soda pop back into...
thingiverse
Initially, it was intended to be printed in different colours to show if the battery was fully charged (green), empty (red) or storage charged (yellow). But then I realized it did a few other things as well. First, it prevents shortcutting the...
thingiverse
... you can use Hex rims/tires. 5.50mm inside-diameter. Print with the pin slot up for no support. Included is a shorter version to have the tires as close to the frame as the original pin tires. ...Contact me if anything is wrong or needs adjustment.
thingiverse
This is a mount for a Castle Creations Mamba-X 8s ESC to a traxxas Maxx (Not X-MAXX). There is space under the ESC for a Castle B-Link and channels to route all the wires. ... the motor mount was made from a $10, 50mm fuel pump bracket.
thingiverse
... trucks. ...I had many truck bodies that I never used. I recently dug out my Revo and wanted to use these bodies but the body mounts didn't fit without drilling more holes. ... These adapters allow you to use your Nitro t-maxx bodies on the Nitro Revo.
thingiverse
This is a front and rear body mount adapter to allow you to mount a traxxas big foot body onto a stock clodbuster chassis. It will work with other clodbuster chassis as long as two conditions are met: 1) that the body mount spacing is the same as a...
thingiverse
Extend the Wheelbase of a Traxxas Bandit or Rustler to have the same wheelbase as the Slash. 46mm extension. This is great if you want to make a Drag car and don't want to change the entire chassis of your existing RC to the LCG Slash Chassis. This...
thingiverse
Needed a adapter for my stampede to except the dboots ragnarock tires. ... this will go from the 12mm to 14mm
thingiverse
This is the STL file for a angled panel mount EC5 connector. ...It is compatible with IC5 connectors as well.