ecig tank protector 3d models

For parking your eCig tanks like the Vivi Nova and the V-Core 2.0 Instructions Print in PLA or ABS In the SCAD: tankDia is the tank diameter (20) wt is the wall width (3) attDia is the attachment diameter (7.5 does the 510) tankHeight isn't the tank...

ecig batt and juice stand test for 3d printer

A vape tank stand for most vape tanks up to 30mm "not tried but specced", Fits onto the Ikea Skadis pegboard :)

Alkaid Tank Protector.

This is a protective sleeve for the Kanger Pangu atomizer. ...Helps avoid breakages if you drop your ecig...but who's done that eh...? ...:)

I create protector for ijust 3 to prevent from opening tank in my pocket. I had to set up in cura "horizontal expansion" -0,05mm to make tight connection (this setting depends on calibration of your printer). ...Dont known why ijust is so wide on a...

New vape atomiser, new tank protector! This is a derivative of my previous model for the Pangu atomiser (https://www.thingiverse.com/thing:1978004). Protects the glass, whilst allowing a clear view of how full the tank is, and also has an opening...

New vape atomiser, new tank protector! This is a derivative of my previous model for the Pangu atomiser (https://www.thingiverse.com/thing:1978004). ...Protects the glass, whilst allowing a clear view of how full the tank is, and also has an opening for...

Helps avoid breakages if you drop your ecig...but who's done that eh...? :) Print Settings Printer Brand: Rostock Printer: ...

Helps avoid breakages if you drop your ecig...but who's done that eh...? ...:)</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Rostock</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Rostock MAX...

A small simple clamp that prevents you from scratching your tanks on the sharp JJ case. ... I recommend to use 2 clamps for each tank (top & bottom).

Fits standard length regulators. ...Has not been check on First Strike or Powerhouse tanks. ...This is a remix of the design from sean13198.

Designed to protect the glass tank (after mine shattered, even with rubber bumpers fitted) Print Settings Printer Brand: RepRap Printer: RepRap Kossel Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 20 Notes: Printed on Anet A8...

This is a cap that can screw onto a paintball cylinder (or any other accessory with the male 0.83-14 threaded fitting) to protect the threads and pin-valve. ... It has a hole for a 2mm line to tether it to the tank/accessory.

Eleaf IJust S tank protector

i made this protector because i always brake my tank

SMOK glass tank protector (minion) 0.2, 20% infill PLA supports are required.

Thread protector for paintball ASA fittings. ... 1" diameter with a knurled finish and 5/8"x18 UNF threads

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hgVg7eRsI0y Aqua One Corner hole protector stop cat paws getting in.

Ecig-Holder battery 25mm and 22mm

To prevent your Ecig from falling down

... ...It's 3mm think so it can protect the glass from your tank better. You can scale it up or down depending on the size of your tank. This is for those that don't like those silicone rubber things or that don't have those accessories at local stores.

This piece pressed down on top of your Vaporesso NRG S tank and removes easily without any tools or effort. The end result is that I can now carry my vape around in my pocket without worrying about it exploding and leaking everywhere like it used...

Can be scaled to fit most tanks, may need slight manual adjustment of size. I used a dremel with a sanding drum and the cover fit so tightly when I dropped it several times the glass broke but the cover held the glass tightly enough to keep a seal.

Ecig Holder d=24mm d=14,6mm d=7mm

ECIG holder so that they can be on the table. ...Can be modified to add charger Print Settings Printer Brand: RepRap Printer: ...

The adjustable power along with a standard 510 connector will accept all vaping devices on the market, atomisers, cartomisers, tank atomisers, ecigs, RBA (rebuildable atomisers) or RDA (rebuildable dripping atomisers). For more advanced vapers. The...

Simple eCig Stand for ten 22mm atomizers Uses 4 M3 srews and 4 standoffs 20mm height. ...Print Settings Printer Brand: RepRap Printer: ...

Summary Simple eCig Stand for ten 22mm atomizers Uses 4 M3 srews and 4 standoffs 20mm height. ... Print Settings Printer Brand: RepRap Printer: Prusa I3 Hephestos Rafts: No Supports:...

Ecig stand 22 x 23 cm with storage adapters for flat atomizers. No support is required for the support. Supports required for the adapter. Turn the cylinder on its small base before slicing. ...