ecobee sensor mount 3d models

This kit is tailored specifically for the 240mm wide structure sensor bracket, with no adjustments required for either the iPad or the scanner itself. ...A 200mm wide iPad Air was used in the photo as a demonstration, and no modifications to the device...

Simple cheap sensor form ali, not linking the actual product link but I have included an image from the product page so you can get an idea of what I'm using. ...Worked for me with alex's firmware out of the box.

This is an attachment for a high-frequency sensor. I had envisioned giving the robot some character to make it more engaging. Feel free to reach out if adjustments are necessary. If you require it to be printed and mailed, please get in touch with me...

This is a bracket I designed to hold my HTC Vive sensor in the conservatory. It hooks over the lip at the top of the conservatory when the roof connects. ... Required: Two M5 x 15 bolts Two M5 nuts Print Settings: Printer Brand: RepRap Printer: Prusa...

This kit was crafted specifically for a 240mm wide structure sensor bracket, and as shown in the accompanying image, an unmodified 200mm wide iPad Mini is more than sufficient to get started, requiring no additional hardware or modifications...

I took the mount made by ssaggers and modified it to mount on my railing for a Halloween project. It's a 19mm square hole for the railing. This could be easily modified for other mounts too. ...

A simple and quick to print magnetic support for Aqara motion sensor.  Requires 4 round magnets, diameter 8mm, width 2mm (real world measurements are more like 7.8mm and 1.5mm). If you want to use other magnets size, the f3d design is included,...

The result is a sensor that not only fits like a glove but also delivers perfectly level prints every time. ...It utilizes a standard M3 screw and nut, paired with a leftover spring from my heated bed - just a bit of filing in the holder's groove and...

Fortunately, the holders worked out perfectly, effortlessly snapping into place around the sensor. A gentle flex along the edge is all it takes. Since they fit so snugly, I didn't bother including screw holes for the module, but if you need them,...

I got from Aliexpress (for few dolars/pcs) some small ZigBee human montion/presence sensors (model: IH012-RT01). Those have Diameter 33mm x 16mm (body) - 28mm height with fresnel lens. Those sensors are powered from CR2450. Might fit for wifi...

I'm thrilled to be giving this a second shot at crafting the perfect shelf for my Oculus sensor, and I have to say, this design is an absolute winner straight out of the build plate, no sanding or finishing required to get the sensor snugly in place....

This are some wallmounts for the Xiaomi motion sensor in different angles (22.5°, 45°, 90°) Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Infill: 25 Category: Gadgets

An (untested) remix for the IR Probe Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Category: 3D Printer Parts

... ... Gets the Sensors off the table. Use Command Strips or 3M Double side tape. .25 layer height, .4 nozzle 2 walls, PolyMAX PLA 215°C 75mm/s 15% infill cubic (in Cura 3.5) 5 layers top, 5 layers bottom. By Super Dave at DC-Concepts.

Держатель датчика протечки воды крепится к стене на двухсторонний скотч, отлив к держателю крепится на защёлках.Wall holder for water leakage sensor with a diameter of 81.5 mm (85.5 mm along the edge) with a removable gutter. Allows you to install a...

Cooling System Mount and Duct Fan for Part Cooling - Engineered with Precision in FreeCAD

The camera lens is precisely centered on an 18 millimeter mount.

Install the Mount Inductive IS500x accessory on your 2040 or 2020 profile to enable endstop functionality.

I've been a big fan of BlaiseB's filament guide runout sensor combo for a long time now, and I've been using it consistently. However, when I recently set up my printer to direct drive, his original design was no longer compatible. To adapt it to my...

Just lift the Sensors off the table and get them out of the way. Use Command Strips or 3M Double-sided tape to secure them. I'm using a .25 layer height, .4 nozzle size, 2 walls, and PolyMAX PLA filament at 215°C with a speed of 75mm/s and 15%...

This is a housing for the standard PIR sensor module, similar to the one sold by Adafruit: https://www.adafruit.com/product/189. It has a 20-degree downward tilt. Three lids are available - one with no side/top obstructions, one with 5mm obstructions...

... that would fit. ...The original design is offset because of the way the sensor is built but my OCD was driving me nuts so I changed the center plug for the bearing and I centered it. ...Figured I would throw it on here with credit to the first post.

Hello, today I'm excited to share this support for the filament sensor with all of you. The distance between the reels is a little larger than the width of the filament roll, and I think you'll really like it. You might need to make the screw holes...

I just modified a MTW fan holder to support an inductive sensor instead, hoping it'll do the trick. The next step will be to rework that design one more time so I can swap out the existing fan for a more high-tech turbine blower positioned right...

This is a compact design for the temperature sensor used in several projects: HMMH - Hour Meter, Magnetic Heater by Rob Silvers - https://www.thingiverse.com/thing:3412516 & Photonsters PTC Heater Unit by Vinicius Silva -...

Magnetic Base Mount for Wyze Sense Motion Detector - Employing 8mm x 3mm Magnets to Secure the Device.

Here is the updated Mount file for PrintrBot Play. ...Please delete the previous version if you have already downloaded it.

Changed the wall mounted version to a magnetic one, by changing the screw slot to a 12x2mm round magnet insert.

Mounts have a tight fit but if the male side is sanded lightly (inside face) the pieces should slide together without excessive force. Mount may crack if you do not sand the pieces. ***Print at 125% size*** Later found I had to sand the inner...

The 10th item is the extrusion of the open area of the cover, which sets how deep the hole is to cover the sensor. The 12th item sets the depth of the magnet. Note: the "Print Settings" below don't have the Prusa Mini+ (which is what this was...