edf motor 3d models
84730 3d models found related to edf motor.myminifactory
3D printable glider edf motor cover mold Video https://youtu.be/EN11xSAg-K8
thingiverse
This is a pinch style motor mount for a 50mm EDF. The inside is 53mm. ...I plan to add holes to the brackets later so you do not have to drill them.
grabcad
Electric ductic fan motor used in model RC vehicles particularly model jet aircraft.
thingiverse
Support for an EDF motor on the ligl glider For his motor https://hobbyking.com/en_us/dr-mad-thrust-40mm-8-blade-alloy-edf-8000kv-motor-330-watt-3s.html
cults3d
Support for an EDF motor on the ligl glider For his motor https://hobbyking.com/en_us/dr-mad-thrust-40mm-8-blade-alloy-edf-8000kv-motor-330-watt-3s.html
grabcad
This is a 1850KV electric ducted fan motor for a 90mm fan. I am using it for a new project, and thought I'd share it. It is rated for up to 22.6 volts and 1650 watts. ... This motor would spin at 1850 X 22.6, or 41,800 RPM!!
prusaprinters
Support for an EDF motor on the ligl glider For his motor https://hobbyking.com/en_us/dr-mad-thrust-40mm-8-blade-alloy-edf-8000kv-motor-330-watt-3s.html Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution:...
thingiverse
30mm ducted fan. ...fits 6015 coreless motor and 30mm tinywhoop 4bladed props. print with a 0.2mm nozzel. Use supports if printing the model with the bellmouth. ...Bellmouth facing down.
grabcad
Brushless performance motor for 69mm EDF. ...Single part file
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2PPoNaBnMlH
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/aAwatmoEtkn
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9c45LgjPcRJ
thingiverse
Mount to use an EDF motor on a wing in a pusher configuration, designed to be zip-tied onto the wing
cults3d
This is an EDF that uses a 775 motor. In version 1.1 I have printed and tested the EDF. I was only able to test it at 6v 5A because of the limits of my power supply. Please reach out to me if you have any suggestions and or questions. Please like if...
thingiverse
Motor housing to be glued to exhaust section once fan and motor are installed. Fan is tight to install, and will ever so slightly catch on initial spool up.The fan should be allowed to gently wear itself in at low RPM for a few minutes, or until the...
thingiverse
This is an EDF that uses a 775 motor. In version 1.0 I have not printed nor tested it yet. I am planning to print it soon. Please reach out to me if you have any suggestions and or questions. NOTE: If you attempt to print and test this model do...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0xG2PoMEHEx
thingiverse
90mm EDF Fan This 11 blade 90mm EDF fan is designed for the Bix3 Trainer 2630 1400kv outrunner motor and propeller/motor mounting hardware: https://hobbyking.com/en_us/hobbykingr-bix3-trainer-1550mm-replacement-motor-2630-1400kv.html This is intended...
grabcad
Very tiny EDF for 3D-printing. ...it can be used for light small scale model aircraft.
grabcad
Propulsion unit Electric Ducted Fan 70 mm with 6 blades propelling fan from QX-Motor redrawing for purposes such as :-fitting in with aircraft model design-replacement for blade or duct damage by using 3d printing.all re-drawing to 3d tracing...
pinshape
I didn't expect that kind of motor be powerful enough for fly models but to drive slower models such as cars, boats. Spec: 50mm EDF, 45mm diameter 9 blades fan. suitable for 130/180 DC motor or similar motor with 20mm diamter. motor shaft 2mm. ...