edge clamp 3d models
128316 3d models found related to edge clamp.thingiverse
Edge clamp that attaches to f-clamp to hold veneer in place on the edge of ply while glue dries. I didn't want to spent a lot on new edge clamps when I will only use them occasionally. Uses M8 threaded rod or M8 bolt and 2 x m8 nuts. There is a...
thingiverse
90 degree clamp to be used to fasted two surfaces together at an angle. Holes made for 1/4 inch bolts. Designed for use with the I.S.A.A.C. ...3-D printer shell (http://www.thingiverse.com/thing:334685)
grabcad
This is the second one, an edge clamp to help pushing the edges while gluing light cracks, more to follow :).To illustrate how it's used see the uploaded images borrowed from: http://www.devonstrings.co.uk/g_vinaccia_repairs.html and...
thingiverse
An edge clamp design I've been experimenting with, previous versions had a taller face but I've lowered it down so it wouldn't interfere with my 3 axis touch plate. The face surface is knurled to try to increase grip. The infill doesn't have to be...
prusaprinters
An edge clamp design I've been experimenting with, previous versions had a taller face but I've lowered it down so it wouldn't interfere with my 3 axis touch plate. The face surface is knurled to try to increase grip. The infill doesn't have to be...
grabcad
Assignment where the body and the jaw are made of AISI 304. ...It also utilizes a SOLIDWORKS Toolbox add-in screw part (annotation: SCHCSCREW 0.5-20x0.5x0.5-HX-C).
thingiverse
A quick thing. ...A spool holder to clamp on the edge of a desk or table. All 3D printed. Fits all the spools I have ever encountered. ... #Thanks!
thingiverse
The clamp base will fit a bed with the slots approximately 37mm apart, edge to edge. The bolt stays fit in the slots and and the clamp base is secured with either wing nuts or the knobs. Once the base is secured, the horizontal bolt applies pressure...
prusaprinters
OverviewThis is a spool holder designed to clamp to the edge of a table and hold 1kg filament spools. The spool rests on printed bearings. The holder also includes a little clip which can hold one end of your filament guide (4mm OD PTFE...
thingiverse
Works with the rolled steel rear edge on these 2 fans (17.375" diameter) Caterpillar FAN:...
thingiverse
It is made to hold a generic Chinese cutting guide clamp and fit in a Rubbermaid upright. I have posted a youtube video about the overall clamp storage rack assembly. Here is a link to the video about the final project. ... https://youtu.be/1Mgr1oDrS7Q
thingiverse
90 degree clamp to be used to fasted two surfaces together at an angle. Holes made for 1/4 inch bolts. Designed for use with the I.S.A.A.C. ...3-D printer shell (http://www.thingiverse.com/thing:334685)
grabcad
A modified version of my previous project Luthier's edge clamp. ...This design gives more control over the positioning of the two parts needed to be glued together and a better placement of the clamp in case of curved contours.
thingiverse
__Apologies as I am not reposting to keep it in the current/newest list.__ **Backstory** I frequently use my Bora Edge Clamp to cut plywood on the floor while suspended on a 3/4" thick sheet of foam insulation board. However, the clamp's handle is...
thingiverse
If it gets delisted, it disappears from your collection. **Backstory** I frequently use my Bora Edge Clamp to cut plywood on the floor while suspended on a 3/4" thick sheet of foam insulation board. However, the clamp's handle is too long to pivot...
thingiverse
Baji is an edge clamping case made for Minidox with specific design choices in mind. Those design choices are as follows: - No external parts (bolts, nuts, glues, etc.) for assembly - Require no switch plates, as far as plate goes you only need...
thingiverse
Works with the FRONT edge on this fan: Caterpillar FAN: https://www.amazon.com/gp/product/B09HK8JCZP/ref=as_li_tl?ie=UTF8&tag=the3dhandyman-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B09HK8JCZP&linkId=6144b58aab20f61419bbf0643e4f9b41 These...
grabcad
Toe clamp Assembly for holding material in place. ...Large t-nut to reduce clamp force on T-track
thingiverse
Edge banding clamp pads for Powerfix clamps from Lidl 1 pair needs - 2x M3 nut, 2x M3x20mm screw, 1x elastic band (2,5-3x7 cm) Standard locking piece should work for most bands. ...Included also thinner and thicker version.
thingiverse
Started from this model, added a channel for position adjustment and used 5MM rod for the slides along with M5x6x7mm knurled heat set nuts. ... If you wanted to update the model, some additional fill could be used around the heat set area.