ee 4 blaster battlefront 3d models
547000 3d models found related to ee 4 blaster battlefront.cults3d
EE-4 blaster rifle 3D print model The EE-4 blaster rifle was the successor of the EE-3 carbine rifle. Its short and stubby barrel allowed it to fire more effectively at close range with spread shots, though this came at the cost of a reduced accuracy...
pinshape
... ...The EE-4 blaster rifle was the successor of the EE-3 carbine rifle. Its short and stubby barrel allowed it to fire more effectively at close range with spread shots, though this came at the cost of a reduced accuracy at range compared to the EE-3.
cults3d
Useful links:https://starwars.fandom.com/wiki/EE-4_carbine_riflehttps://www.youtube.com/watch?v=Q6PuIluEfLI&ab_channel=SphagnumPI
pinshape
Model dimensions: - length – 355 mm - height – 186.5 mm - width – 100 mm The model consists of parts: Barrel front short rib 1-3, Barrel part 1-3, Barrel rear short rib 1,2, Barrel rib 1-9, Body part 1-6, Front handle grip 1,2, Front handle screw...
cgtrader
... ...The EE-4 blaster rifle was the successor of the EE-3 carbine rifle. Its short and stubby barrel allowed it to fire more effectively at close range with spread shots, though this came at the cost of a reduced accuracy at range compared to the EE-3.
pinshape
... The rifle consisted of a small handle attached to a long circular barrel. An alternate version of this model features a modified scope mounting and hand grips that run the length of the barrel. http://battlefront.wikia.com/wiki/EE-3_Blaster_Rifle
cults3d
... The rifle consisted of a small handle attached to a long circular barrel. An alternate version of this model features a modified scope mounting and hand grips that run the length of the barrel. http://battlefront.wikia.com/wiki/EE-3_Blaster_Rifle
sketchfab
EE-3 Blaster Rifle 3D print model The EE-3 carbine rifle was a blaster that was modeled after the E-11 blaster rifle used by Imperial Stormtroopers. The rifle consisted of a small handle attached to a long circular barrel. An alternate version of...
thingiverse
I couldn't find a good lego EE-3 so I threw one together. Scale should be correct. Print at an angle with supports for the best result. ...Use resin if you can.
thingiverse
A custom scopeless EE-3 Blaster from star wars, modeled in autodesk inventor by myself. Build Video Can Be Found Here ! ... https://www.youtube.com/watch?v=gGK7BeAAhAs
sketchfab
A weapon favored by mercenaries, bounty hunters, and mercenaries alike, the EE-4 was a powerful and compact blaster carbine that was used throughout the galaxy during and after the fall of the Republic.
thingiverse
The CA-87 is a retro-fitted Jawa blaster that is extremely deadly at short range, but near useless at medium and long range.
cults3d
The DLT-19 heavy blaster rifle was a model of blaster rifle manufactured by BlasTech Industries. They were used by stormtroopers of the Galactic Empire, as well as by the bounty hunter Dengar, and some heavy troopers of the Alliance to Restore the...
thingiverse
As i could not find a proper Stand for the EE-3 Blaster, i decided to give my little knowledge about 3D modeling a chance and put together this little Blaster stand in Blender. This Stand is about 13 cm´s (or 5,11 inch) tall, so the stock part will...
thingiverse
This is a mounting piece for the EE-3 Blaster model by AprilStorm: (http://www.thingiverse.com/thing:150686) This piece has a peg that can be inserted into the top of the blaster model if slots are cut into the model. The scope clamp included with...
sketchfab
a cyberpunk-ish version of Boba Fett’s blaster from the Star Wars franchise
thingiverse
The holes in the model are for for wooden dowels/metal rods(about 1/4 inch ones, though i had to use some tape to fill in some space) throughout the stock, scope and barrel. Use the exploded diagram to figure out where everything goes, might do a...
prusaprinters
The holes in the model are for for wooden dowels/metal rods(about 1/4 inch ones, though i had to use some tape to fill in some space) throughout the stock, scope and barrel. Use the exploded diagram to figure out where everything goes, might do a...
thingiverse
I managed to print one full blaster, but believe I can separate the parts better, also the stock is a little off. Also, as a warning, some parts may not be 100% correct scale, so check before printing. This is a complicated multipart build. I would...
pinshape
Model dimensions: - length – 795.3 mm - height – 196.2 mm - width – 70 mm Model consists of parts: barrel bar 1-16, barrel part 1-4, body left insert, body right insert, body, grip, hammer, handle, rear insert 1, rear insert 2, scope disk 1, scope...
myminifactory
S-5 officers blaster pistol from starwars battlefront 2 and used in the movies.
myminifactory
DL-18 blaster pistol used in starwars and starwars battlefront. ...Perfect for a prop or cosplay
myminifactory
This blaster pistol is used by the officer class in starwars battlefront 2.
myminifactory
This blaster pistol is used by Poe Dameron in episode 7 and 8, but is also used in Starwars Battlefront 2
cults3d
The TL-50, also known as the TL-50 Heavy Repeater, is a fully-automatic Heavy Blaster in DICE's Star Wars Battlefront and Star Wars Battlefront II. Besides its high rate of fire, the weapon is most notable for its unique secondary action that allows...
prusaprinters
Update: fixed a void I found in file, standard versions fixed, will upload fixed versions of the chunky files as I get time to do so. Howdy, still a learner at 3D modelling, I have today my attempt to create the DC15 blaster pistol from the OG Star...
cults3d
Howdy, still a learner at 3D modelling, I have today my attempt to create the DC15 blaster pistol from the OG Star Wars Battlefront games from 2005. The reference images available for this blaster are limited but I did my best to make it as accurate...