eevee 3d

For the majority of items, the mesh origin has been set so that when you import these objects into your 3d editor of choice, they are positioned as they would be on the sample ships provided. When comparing parts, you’ll notice some ships and parts...

**We need for the fire fighter box car** * 1x front without seat * 1x front with seat * 2x single window side parts (one should be mirrored in Cura) * 1x floor (you decide with or without T-head couplings) * 1x roof with brake man seat * 2x wheel...

I give you the 3D printed Sterling main spring forming tool...https://i.imgur.com/j04a7Tb.jpgIt is simply a grooved shaft set to the correct diameter and pitch of a Sterling main spring. The shaft is hollow, allowing you to slip it over a section of...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

We've found a Drawer_Gap of 1.0 (mm) to be sufficient, but results will vary for different 3D printers. If unsure, you can test the gap by printing a drawer of your chosen dimensions and a chest for a single drawer (Drawers_Across set to 1 and...

Make your own custom chips. Accessories DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what...

The field is confined by a steel “yoke” that forms the bulk of the detector’s 14,000-tonne weight.CMS acts as a giant, high-speed camera, taking 3D “photographs” of particle collisions from all directions up to 40 million times each second. Although...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

You will most likely have to do some sanding to get it to work smoothly. It is intentionally designed to be a bit tight due to the nature of 3D prints and how layer lines will wear over time. I'd rather it be rougher at first and smooth later than...

If not, here is a good pair you can buy (local hardware store is the best option):...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

At this point we are reaching out with the 3d printing community and are looking for help. Everything was designed on Tinkercad. If you need me to share my Tinker stuff so you can edit it, just let me know. I added 3-4 different choppers. The...

The purpose of this assignment was to develop our collaboration and 3d modeling skills to better prepare us for future, more complicated, projects. Assembly Instructions:  Constraint Box: Use the rectangle tool to make a 6 x 13 cm box, make sure to...

For example the main part needs to be turned 180°.Also use as much cooling as your current setup is capable of!PLA will NOT work for the main part as things will probably become too hot and soften PLA, use PETG (or ABS) instead.Category: 3D Printer...

Use at own risk, you may have to reprint them later.------------------------------------------------------------------------------------------------------Voron Stealthburner Beta for Creality Spider V1 hotend with Orbiter 2.0 extruder (direct drive)...

###Latest version (v4.0): https://www.myminifactory.com/object/3d-print-169440 ***This is my second attempt on creating a mechanical tally counter. Maybe not the most ergonomic counter in the world, but it's quite satisfying to use. It also solved a...

Depending on your model of 3D printer, you now have the choice to use the original slide that's 0.25mm smaller or the new one that's overall 0.5mm smaller. The only pain in the butt part at this point is removing the support structure from the...

(The face of the slot machine should point down towards the print bed.)Use standard settings and 0.2mm layer height.The slot machine is fully print-in-place: No assembly required, just remove the slot machine from the print bed and play! The...

...Nails and 3D printed parts are cheap and easy to replace. 7.6mm fits best. Any nail with Ø6-7.8mm (8mm model) and a length of at least 15-20cm should work. I'll add a 6mm model for smaller nails but they may be to short or don't stick in the ground.

###Anet A6 E3D Hemera Carriage This carriage design for the Anet A6 3D printer is suitable for both the E3D original Hemera and the shorter and lighter E3D Hemera XS extruder. The parts are added to equip the Hemera with the E3D Revo, V6, Volcano or...

There is a bit of tolerance built into this to make it a tight fit with respect to the slight shrinkage that happens in 3D printing. Be prepared to use clamps to squeeze the nut into place. Mine was able to just push in with my thumb. - qty. 2 of...

###Latest version (v4.0): https://www.myminifactory.com/object/3d-print-169440 ------------------------------------------------------------------------------------------------------------- * ***This is my second attempt on creating a mechanical...

Each level is divide in eight parts no larger than 27cm, you need to have a bigger printer, or you could split them by yourself using Microsoft 3D Builder, Tinkercad, or similar to those. As it's a very big model, I know many people would want to...

Because of this I figured it would be nice to dig up the old 2D drawings and turn them into a 3D model so you can print your own Fauvet Girel and motorize it with relatively little effort. I also provided parts for a dummy model in case you want to...

There is a wide range of radius sizes from 5mm up to 200mm and 0.5" to 8", all carefully optimized for best usage.About the DesignI designed all templates from the ground up, specifically to be printed on a 3d-printer. The design is optimized to make...

But it can be detached to service the servos in the fuselage.As a pilot you should have some experience, as in my opinion 3d-printed models are not suitable for beginners. The model is capable of rolls, loops, inverted flying and maybe more. But as...

I had to make a lot of modifications to get it to work and updated the 3D model accordingly. That's why it looks different. -I am not and will never pretend to be an engineer. I have no idea about the cooling efficiency of this design. Just a dude...

It features a very slightly bigger gear ratio - but it's main advantage is that the printed spur-gear from that design requires a very accurate/calibrated 3D-printer while this doesn't.FeaturesNEMA17 gearbox3:1 gear-ratio (38/12T, so a reduction of...

If it leaks, you may find tips in the community about glues that can be used to coat the inside, but it's been a very reliable for me.Note: In their blog post on watertight printing, Prusa recommends a minimum of 4 perimeters for PETG and PLA. Using...

For triangles, we also decided to not measure the length of the hypotenuse but rather measure the height and width of the imaginary triangle, to make it more defined in Solidworks when we would eventually sketch and make the 3D model. Our final and...