eew 6 3d models
359556 3d models found related to eew 6.thingiverse
This is eew 6 tripod base for people who wants to mount their eew 6 on a tripod. You'll need a nut that can fit the screw on a standard tripod mount. Mine uses 20 thread size. I would go to a hardware store with your tripod to find a nut. ...
thingiverse
### Reducer This part fits into the orifice hole on the front of your EEW 6.0. It helps reduce the yarn wobble when spinning thin yarn. After printing you may need to sand it's diameter slightly to make it fit better, or if the fit is too loose...
prusaprinters
You can reuse the screws and rubber feet from the bottom that came with the EEW 6.0.Flyer Arm CapsThis part clicks onto the end of the flyer arms.ReducerThis part fits into the orifice hole on the front of your EEW 6.0. It helps reduce the yarn...
thingiverse
this is a simple tripod base for eew 6. V2 has no nut. The camera screw is in the 3d print itself. ... You'll need 4 of number 8 wood screws about 1/2 inch long.
thingiverse
These are the parts needed to print a bobbin winder attachment for the EEW 6.0. Normally the EEW 6.0 spins fiber into yarn. However, if you remove the flyer and use this bobbin winder it allows you to quickly wind bobbins. The only parts that...
thingiverse
This is an alternative hook option for the EEW 6.0 eSpinner. ... https://www.youtube.com/watch?v=WvHSGPTJA6o
thingiverse
Based on the Craft Me Happy Nano Twist Keeper design and the orifice reducer for the EEW 6.0 made available by Maurice.
thingiverse
I have released a different version of this bobbin that prints in 3 parts instead of 4. However, by breaking this into 4 pieces it requires less supports and the final print is nicer. BobbinDisk 2 and BobbinTube do not require supports. ...
prusaprinters
<p>These coil yarn guides clip into the metal hooks. These are useful when spinning coil yarn which can get caught on the metal hooks and should help with any other non-uniform bulky yarn that gets stuck on the metal hooks.</p><p>Here is a video...
prusaprinters
<p>I have released a different version of this bobbin that prints in 4 parts instead of 3. However, by breaking this into 4 pieces it requires less supports and the final print is nicer.</p><p>BobbinDisk 2 and BobbinTube do not require...
thingiverse
These two files are decorative ends for Maurice's EEW6 bobbin. To complete a bobbin, look at the original design and print his Bobbin Disk 1b and the Bobbin tube. Print his two items and these two items. It takes 4 pieces and the two bearings that he...
thingiverse
These two files are decorative ends for Maurice's EEW6 bobbin. To complete a bobbin, look at the original design and print his Bobbin Disk 1b and the Bobbin tube. Print his two items and these two items. It takes 4 pieces and the two bearings that he...
thingiverse
These coil yarn guides clip into the metal hooks. These are useful when spinning coil yarn which can get caught on the metal hooks and should help with any other non-uniform bulky yarn that gets stuck on the metal hooks. Here is a video showing...
thingiverse
Quill spindle for the EEW 6.0 and the EEW nano. Alone, it fits the 6.0, when o-rings are put in the two grooves, it will fit the nano. ... It is in two parts which screw together to minimise waste when printing.
thingiverse
This is a eew nano reducer modified to fit #8 Clover bamboo neelde so you can spin quill style on the eew nano. ... You will need two size 012 o-rings to hold it in the spindle.
thingiverse
it's a simple box case for eew nano so you can put the eew nano to whatever bag that fits but not worry that the wheel be damaged.
thingiverse
... ... It gives you another method of spinning yarn on these spinning wheels. There is a video that shows how this quill is used at: https://www.youtube.com/watch?v=aegSOofi6BU If you have more questions about the EEW Nano visit: www.dreamingrobots.com
thingiverse
The end cap fits into the orifice of the EEW nano, and then a bobbin shaft is attached to the 3d print along with a second EEW nano bobbin cap. Like the quill, clear tape may need to be added to the end, so that it will fit inside the EEW nano...
thingiverse
Eew tub drain hair trap 40mm D x 22.5H, place back water stopper. ...Enjoy hot tub while still protected, two layer protection.
thingiverse
This is an orifice reducer for the EEW Nano. ... You will need two size 012 o-rings to hold it in the spindle.
thingiverse
Another yarn guide for the EEW Nano e-spinner. ... This one has a rounded guide for the yarn, so it experiences less resistance.
thingiverse
... the EEW Yarn Counter. ... It can be printed without any supports. Here is a video that gives more information about this case: https://www.youtube.com/watch?v=WjhCusyz2Iw To learn more about the EEW Yarn Counter visit: https://www.dreamingrobots.com/
prusaprinters
... EEW Yarn Counter. ...It can be printed without any supports.Here is a video that gives more information about this case: https://www.youtube.com/watch?v=WjhCusyz2IwTo learn more about the EEW Yarn Counter visit: https://www.dreamingrobots.com/
prusaprinters
These are various parts for the EEW Cone Winder. </p><p>There are some Fusion 360 files which allow you to generate cones or tubes of different sizes. ...Below is a video that goes into depth about how those works.</p><figure class="media"><oembed...
prusaprinters
It gives you another method of spinning yarn on these spinning wheels.There is a video that shows how this quill is used at: https://www.youtube.com/watch?v=aegSOofi6BUIf you have more questions about the EEW Nano visit: www.dreamingrobots.comA few...
thingiverse
There is a Kickstarter for this project at: https://www.kickstarter.com/projects/dreamingrobots/electric-eel-wheel-mini-2 You need to print 1x eew_mini2_bobbin_tube and 2x eew_mini2_bobbin_disk per bobbin. The disk has a tight and loose option. If...
thingiverse
This is a cover for the bottom of the EEW Mini 2 and also holds a battery. ... It is designed to work with this battery pack: https://www.amazon.com/gp/product/B01M7Z9Z1N It also requires 4 #8 half inch screws: https://www.mcmaster.com/92470a194
thingiverse
This is a peg and hole to be used with a spring and cord on the EEW nano espinner to make the scotch tension system more easy to make small adjustments than when using the elastic band that comes with it. Use superglue or similar to attach the hole...
thingiverse
This is another bobbin for an EEW Nano ( v 1.x ) mini e-spinner. Everything can be printed without support. Depending on the adhesion of your build plate, it might be wise to print the tube with a brim. Probably the axle holes need to be...