eew mini 3d models

These are an optional accessory that I make free to the community to replace the metal sliding hooks that come with the EEW Nano.I recommend printing 4 of them and putting 2 on each arm so that everything stays balanced (this helps reduce...

It works with both the original EEW Nano 1.0 and the EEW Nano 1.1.It is designed to work with this battery pack: https://www.amazon.com/gp/product/B01M7Z9Z1NIt also requires 4 #8 half inch screws: https://www.mcmaster.com/92470a194For more fiber...

Another yarn guide for the EEW Nano V1.x e-spinner. This one has a rounded guide for the yarn, so it experiences less resistance. ... Not for the Nano V2.x!!!!

... For proper installation, download and run the nut_test.stl file to verify that you have acquired the correct nut for your tripod model. In addition to the base platform, four #8 1/2 screws are necessary to attach the eew nano securely.

... a hole reducer for EEW6 e-spinner bobbins to fit a Lazy-Kate from Majacraft, Shank or Ashford (or custom made) with a shaft diameter of 8 mm. ...The diameter of the EEW6 bobbins is 3/8 inch (about 9.5). This also works for the bobbins of the EEW Nano.

This is a version 2 of eew base for tripod. I removed the nut and put it camera screw hole in the middle. Much better because in V1, the nut can fall off even with glue. ... You will need 4 of number 8 wood screw about 1/2 inch to mount the nano.

... a hole reducer for EEW6 e-spinner bobbins to fit a Lazy-Kate from Majacraft, Shank or Ashford (or custom made) with a shaft diameter of 8 mm. ...The diameter of the EEW6 bobbins is 3/8 inch (about 9.5). This also works for the bobbins of the EEW Nano.

I designed a miniature case for my eew nano's motor, specifically to keep it cool. This updated model provides a wood block base for added stability, allowing users to place the micro fan on their preferred surface. ...The original design involved...

... hole reducer for EEW6 e-spinner bobbins to fit a Lazy-Kate from Majacraft, Shacht or Ashford (or custom made) with a shaft diameter of 8 mm. ... The diameter of the EEW6 bobbins is 3/8 inch (about 9.5). This also works for the bobbins of the EEW Nano.

I wanted a prettier orifice reducer for my EEW Nano electric spinning wheel, so I put the design from my spiral spindle onto the disk. It goes nicely with my Celtic knot bobbins.Prints flat, no supports needed. ...You will need to o-rings called for in...

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the "gf" (requires glue) or "pf" press fit disks per bobbin. NOTE: The "flat" end is an experimental disk that makes a bit more space on the...

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the "gf" (requires glue) or "pf" press fit disks per bobbin. NOTE: The "flat" end is an experimental disk that makes a bit more space on the...

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the "gf" (requires glue) or "pf" press fit disks per bobbin. NOTE: The "flat" end is an experimental disk that makes a bit more space on the...

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the "gf" (requires glue) or "pf" press fit disks per bobbin. NOTE: The "flat" end is an experimental disk that makes a bit more space on the...

This updated design boasts an interchangeable screw-on bobbin rod and knob, streamlining transportation and versatility as a universal yarn plying tool for various spool sizes. By customizing the height and width of the rod using the provided...

These spindles, known as bobbins, serve the Electric Eel Wheel 5.x spinning wheel. ...For the bearing-equipped model, select two R6-2RS bearings for each spindle.

This is a 3D-printable motor pulley to replace the stock one on a Dreaming Robots Electric Eel Wheel Nano. It'll work with either the v1.0 or v1.1 motor, and you may need a drop of CA glue to secure it to the motor shaft. ... This is the pulley that I...

This is a threaded bobbin for theDreaming Robots Electric Eel Wheel Nano. It's designed to be printed without supports, though I do use a raft for the tubes (to make sure the ends aren't too squished on the bed). I sell these and a few other bobbins...

These are bobbins for the Electric Eel Wheel 5.x spinning wheel. ...There is a version that uses bearings and if you choose that one you need two R6-2RS bearings per bobbin.For more fiber tools see our store at: www.dreamingrobots.com

This is a custom bobbin designed specifically for the *Dreaming Robots Electric Eel Wheel Nano*. I intentionally crafted it to be printed without any support material, although I do use a raft for the tubes to prevent distortion on the bed. ...For your...

Print out one tube and two discs, and make sure they fit perfectly together by drilling a small hole into each disc if necessary. ...Now, securely attach both discs to the tube using strong adhesive.

End to make a bobbin for the EEW Nano from the core of a roll of 80mm receipt paper (cores are 21.5-21.7mm in diameter, roughly). Print this with the socket down and the pulley up! ...The default orientation is upside down.

... from shifting around excessively, I've added a bit of felt inside the case. When designing this case, I drew inspiration from both the original EEW battery case on Thingiverse and another design by Snortimer also available on the same platform.

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of these loose (requires glue) or (snug) press fit disks per bobbin.NOTE: The "flat" end is an experimental disk that makes a bit more space on...

You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the loose (requires glue) or (snug) press fit disks per bobbin. NOTE: The "flat" end is an experimental disk that makes a bit more space on...

A 4-bobbin Lazy Kate designed specifically for EEW Nano bobbins with options for solid arches, pieced arches for smaller print beds, tension or non-tension feet that allow printing without supports. Print the feet upside down (pins down), bobbin...

This redesigned nano bobbin disc eliminates the need for supports thanks to a modified shaft socket that matches the original profile, ensuring it works seamlessly. The shaft has been reengineered with increased surface area at each end, addressing a...

The original design ask that this piece be drilled open. ...I resized the center to fit the nano without needing to drill.

It's a compact fan housing designed specifically to keep tiny motors at an optimal temperature.