ego stubby nozzle 3d models
74419 3d models found related to ego stubby nozzle.cults3d
Wall mount for the nozzle scaled at 101.5% (the orginal design is too small)
thingiverse
Wall mount for the nozzle scaled at 101.5% (the orginal design is too small)
prusaprinters
Remix from https://www.thingiverse.com/thing:4841242Wall mount for the nozzle scaled at 101.5% (the orginal design is too small)Category: Tool Holders & Boxes
thingiverse
Order on Etsy - https://www.etsy.com/listing/1047295234/stubby-car-drying-nozzle-for-ego-leaf Order on Facebook - https://www.facebook.com/marketplace/item/1422477248121606/ ~ 7" long stubby car drying nozzle ~ Not compatible with the Blowerband™...
thingiverse
I was searching for the EGO stubby nozzle to print and noticed all of those files were taken down. I had printed one for my EGO 530, but just upgraded and needed the newer design file. Very glad that Vehicular created this version to use - thank...
thingiverse
Stubby attachments for EGO leaf blower. Neither have been tested for efficiency, just for fitment. Made for Ego 650cfm blower but may fit others. Inside diameter is 97mm and is a tight fit. ...Slight adjustments wouldn't hurt.
prusaprinters
It fits an EGO 530, 575, 580, or 650 blower which can make it easier to dry off your car than the much longer original EGO nozzle. I shortened it to be able to print on a <a...
thingiverse
Tips: Print in PETG for UV protection and strength Use a brim so it doesn't fail like mine did twice Change Vertical Shell Perimeters to 4 100% Infill (It adds minimal time and minimal filament on this model) I used a .6 Nozzle with in .40mm Draft...
thingiverse
This is a simple nozzle for the Ego brushless blower, normally they charge $12 for something similar
thingiverse
... tube is 3 1/4" inside diameter, and the Flat Nozzle inside diameter is 3.5". I designed this in 3D TinkerCad. I added a tab to fit inside the EGO Flat Nozzle Clip Time to Print on a Taz 5 is Less than an hour (59M) and takes 23g of filament.
thingiverse
This is my take on a BlowerBand for the Ego blower Short Nozzle. This band should protect your car from scratches if you accidentally bump the nozzle on it. This is my first design. Printed in TPU. ...
thingiverse
Designed this to replace the Nozzle for the EGO leaf blower. ...I designed it to be print with ASA, so you might need to adjust it, since ASA have more shrinkage.
prusaprinters
[See "Does it work?" below before printing this!] This nozzle attachment is for the EGO cordless blower model LB5300 (see photos), but may fit other EGO cordless blowers as well; see the included drawing for relevant dimensions. This blower is sold...
thingiverse
I designed this stubby nozzle for Scott Leaf blower, so I can maneuver easily when I'm drying my care. ...Designed and printed for ASA, so you might have a little bit slack if using other material
thingiverse
This is a stubby nozzle for the Milwaukee M 18 blower. This is used for blowing water off your vehicle, cleaning up a shop, places with tight quarters. There is a short one piece version, a long version and a long two-piece version depending on the Z...
thingiverse
... fit of the AnnArborWorx's TwistLock will start to lose its effectiveness. This TwistLock version is a detent rib that you pop over when attaching and then again when detaching the nozzle. ... The detent also gives a very satisfying feel and sound.
thingiverse
I wanted a short tool with some leverage to easily change over hot end extruder nozzles. Turns out this is a stubby hex handle you could use for any hex tool bits. ...It is designed to fit a hex to 1/4 square adapter on which you can add 1/4" sockets.
thingiverse
mr stubby you must buy a 3/8 hexxy wexxy hexxy wexxy https://smile.amazon.com/gp/product/B01N5BVBSZ optional: two 2mm x 20ishmm pinnywinnys pinnywinnys https://smile.amazon.com/gp/product/B07M63LPFD build instruct print with petg or something strong...
thingiverse
... stages, and the sketches and parts, so it is easier for you to see what is what, and what you could adjust. I made the button thicker, nozzle shorter, tube section wider (2mm up from 1mm) for creamy fluids and the neck wider for my can's spout.
thingiverse
... the body and the tip with a twist lock. Replacing nozzle just need to print the front part. A round and a flat nozzle were made here. A bare twist lock ring with no nozzle is included for anyone who like their other nozzle shape add on top.
thingiverse
FIL wanted this for his electric leaf blower. It locks into place with the nubs on the extension piece. I printed this a few months ago so I forgot to take pictures of it attached but it works Printing: Used PLA with regular settings. Some...
thingiverse
... fit of the AnnArborWorx's TwistLock will start to lose its effectiveness. This TwistLock version is a detent rib that you pop over when attaching and then again when detaching the nozzle. ...The detent also gives a very satisfying feel and sound.
prusaprinters
People also like these nozzles for drying their cars after washing. I printed at 1.5mm line width using a 0.8mm nozzle and 0.3mm layer height on my Ender5Pro (stock hot end and extruder). I have stock cooling, so I limit my flow rate to 10mm3/s....
prusaprinters
This one has a sweep/broom/wide opening, especially useful for drying your car. I printed at 1.5mm line width using a 0.8mm nozzle and 0.3mm layer height on my Ender5Pro (stock hot end and extruder). I have stock cooling, so I limit my flow rate...