egpu case 3d models
203589 3d models found related to egpu case.grabcad
EGPU design with flex/1U power supply, AD_LINK R43SG graphics card bracket, and 2.5 slot graphics card size.I use an MSI Ventus 3070 Ti, which fits fine with extra space.
thingiverse
Case for eGPU adapter V8.0 EXP GDC Beast with place for ATX power supply. Designed for cards up to 30cm long. Walls of case was cut from 3mm black plexiglas, to connect every piece of case I used M3 screws. ... Print Settings Rafts: ...
thingiverse
Wanted smallest eGPU case for my new GTX 1050Ti from ZOTAC and PE4L v2.1b eGPU adapter No options on market at all, and if so, very pricy and bulky. So I´ve made my own. Works pretty straight out of the "printer"... Material needed: 4x 3x30mm...
thingiverse
I wanted to travel with my eGPU and found the box that came with the Akitio Thunder too heavy, so I pulled the board and printed this encosure to protect it when i travel but keep it light. I then soldered onto the motherboard in two places, and...
thingiverse
Needed to place my Akitio Node on its face for cable length reasons (the thunderbolt 3 cable is only 0.5m to allow for faster speed transfer), but this eliminated the usefulness of the Node fan, which was pressed against the floor. ...This riser has...
thingiverse
Hi Everybody, thanks for all the models you shared with the community. This is my first own project worth to share. I got myself a PCI riser x1 -> x16 to b able to utilize my 2nd GPU (AMD W4100). So i made myself a cover for the PCI riser and...
grabcad
eGPU case for laser or waterjet cutting. ...Possible to assembly without metalsheet bender.
thingiverse
This case suitable to exp GDC with an old Asus 750 Ti with express card/minipcie external VGA Notebook also add .f3d for custom build fusion 360 enjoy using m3x15 and nuts for combine front case and back case on bottom, side, upper, and handle. ... ...
cults3d
+better airflow +any long graphics cards +internal power supply +smaller footprint 9h printing time at 0.3mm layer height Size: 230 x 186 x 87 mm
thingiverse
Mantiz Venus is a very popular EGPU case with built-in USB hub and SATA port, but it ships with only 2.5inch SSD holder inside the box. After installing a Curical MX500, I found that the actual transfer speed is limited at 300+-MB/s, and even with...
myminifactory
This is a eGPU designed for ADT LINK R43SG-TB3 riser & SFX power supply .
thingiverse
This is a eGPU designed for ADT LINK R43SG-TB3 riser & SFX power supply . ... ...
thingiverse
This shelf is designed specifically to hold a Razer Core X eGPU and is sized to fit the legs of the Ikea Bekant desk frame, but it could also be used to hold a SFF PC case. There are holes sized to accommodate 1 inch wide straps if extra security is...
prusaprinters
This bracket can be used to lay the BMD eGPU or eGPU pro on its side instead of it standing vertically. It has slots in various areas to run straps through to secure the eGPU to the bracket. I use them to mount the eGPU in a rack on a vented rack...
cults3d
An under desk mount for the Alienware eGPU for Alienware laptops. Rectangular design with hexagonal accents. x2 mounts recommended to hold the eGPU. ... Slightly oversized to allow for the addition of padding or other desired supports Easy to print...
thingiverse
Certain models of Aorus eGPU have a flaw in the typeC/thunderbolt 3 port where it's about 2-3mm too shallow, and allows the cable to move with too much play, causing frequent disconnects. this simple fix is made to be superglued to the outer case,...
thingiverse
I bought a Razer eGPU box to expand my laptop, but it's too big and heavy. It takes up too much desk space, so I designed the foundation for placing it vertically. Print two of each part, flat side down. No support required. The corner parts...
myminifactory
The prints consist of 3 parts, - Base: holds all items - Thunderbolt casing Clip: secures the small thunderbolt casing from the ADT-link in place by 2x M3 screws - Lid: Flat plate to close off the enclosure. Parts have been designed to not...
thingiverse
A stand and support for a GPU to be mounted on top of a ATX PSU. Printed in PLA at very rough settings (0.28 height, 3 perimeters, 10% infill) turned out very good. ...
thingiverse
... is connected with the front plate. With the new base plate the length limitation of the eGPU box is removed. The screw holes for the PCB are designed for M3 inserts. ... Note that you may have to solder an extension to your 24 pin ATX connector.
cults3d
My Akitio Thunder 2 eGPU setup with the MSI AERO GTX1060 6GB graphics card and dual Noctua 60mm fans was still getting warm during gaming even after a little bit of case modding. I noticed the stock perforated cover on the Akitio Thunder enclosures...
thingiverse
My Akitio Thunder 2 eGPU setup with the MSI AERO GTX1060 6GB graphics card and dual Noctua 60mm fans was still getting warm during gaming even after a little bit of case modding. I noticed the stock perforated cover on the Akitio Thunder...
prusaprinters
My Akitio Thunder 2 eGPU setup with the MSI AERO GTX1060 6GB graphics card and dual Noctua 60mm fans was still getting warm during gaming even after a little bit of case modding. I noticed the stock perforated cover on the Akitio Thunder enclosures...
thingiverse
A custom eGPU enclosure designed for the PCB from an AKiTiO Thunder2 (other AKiTiO PCBs may work as well). Sized to fit an MSI Aero ITX GPU. Screw holes sized for #4-40 machine screws. May use metal insert from original enclosure to help hold GPU in...
thingiverse
Original didn't fit my RX570 8gb, so I adapted the part. Should fit but I'm still waiting for the print to finish. This should work with the original front and back since the height will be unaltered. All three files have been edited and I am...
thingiverse
This is a remix of "eGPU Enclosure for Nvidia GTX 1060 and EXP GDC Beast (v8.x) by ZodiusInfuser". My Asus ROG Strix Radeon RX570 would'nt fit, as it is longer than the GTX 1060. So, the only thing I had to do, was enlarging the front of the case...
thingiverse
Oh and it has RGB LEDs and a front mounted controller, along with a connection at the rear to plug in any external RGB lighting, such as my laptop underglow: https://www.thingiverse.com/thing:2974926 **The enclosure consists of 7 unique parts:** * 1x...