eheim automatic fish feeder instructions 3d models

I needed a simple stand for my Eheim automatic fish feeder, so I designed this to clip onto the edge of my Aqueon 90g tank. I've included a sketch of my tank's rim in case it helps. Rather than build walls to keep the feeder on the stand, I designed...

this is an automatic fish feeder with a roller hole mechanism

this is an automatic fish feeder with a roller hole mechanism

This automatic fish feeder delivers fish food automatically using a HiTEC HS-422 servo that spins 180 degrees to dispense the food, then rotates back 180 degrees to refill. The feeder holds a significant amount of flake or small pellet fish food in...

This is a Eheim Automatic Fish Feeder replacement food compartment. The original was not as accurate as I needed so I created this. This compartment uses inserts for small, medium and large dosing. ...I made this specifically for small pellet food but...

fixation for the automatic fish feeder cy-039 with funnel for the tecatlantis aquariums. The funnel is designed for tecatlantis aquariums to fit on the fead flap

My aquarium lid is not designed to fit an automatic fish feeder. And an automatic feeder is an extremely useful thing. Sometimes just necessary. I designed this mount for Tetra myFeeder. I used M3 screws and inserts for fix the mount plate. ...I...

fixation for the automatic fish feeder cy-039 with funnel for the tecatlantis aquariums. The funnel is designed for tecatlantis aquariums to fit on the fead flap

I cut a small hole in the lid of my aquarium so an automatic fish feeder can drop food into the gap between the wall and the lid. ...This allows me to feed my fish without lifting the lid, which is essential for keeping it in place.\r\n\r\nThe bracket...

This 3D model showcases an automatic fish feeder, utilizing a standard plastic bottle - specifically, a plastic Coke container or a standard 500ml water bottle - as the loading vessel. At present, no coding or automation has been integrated; however,...

This is an automatic fish feeder based on a Raspberry Pi Zero and an SG90 servo. It features a sliding door actuated by the servo to drop food into an aquarium below based on open time and sliding speed. ... You will need 4 2.5mm x 8mm screws to...

Here is the rewritten text: This DIY Fish Feeder is a clever device that automatically feeds our fish when we're away from home. To build it, you'll need the following parts: two M3x10 machine screws, two M3 nuts, one LS-0006 servo (or adjust the...

An ongoing project, this automatic fish feeder uses an Arduino board that rotates the auger every 12 hours to feed fish. A manual override switch lets users feed fish any time. The previous cardboard feeder inspired a 3D-printed upgrade. Updates...

Remix from https://www.cgtrader.com/free-3d-print-models/hobby-diy/automotive/automatic-fish-feeder-e87279af-0604-4faa-89e1-273e2bbb7a9f Changes: - Glass size to 11mm (my aquarium has 10mm) - Tilting of the container for the food to fall out more...

After trying several other automatic fish feeders listed online with no luck, I decided to design my own system. The feeder is specifically designed to dispense small food pellets such as Top Fin Betta Bits shown in the photos. A circular hole on the...

I tried several of the other automatic fish feeders listed online, and didn't have much luck, so I designed my own. It's designed to feed small food pellets, such as the Top Fin Betta Bits shown in the photos. The feeder arm contains a circular hole...

I tried several of the other automatic fish feeders listed online, and didn't have much luck, so I designed my own. It's designed to feed small food pellets, such as the Top Fin Betta Bits shown in the photos. The feeder arm contains a circular hole...

An automatic fish feeder. The pushing and pulling motion is achieved by this Bluetooth smart fingerbot https://www.amazon.com/dp/B0B97G3B8G?ref=ppx_yo2ov_dt_b_product_details&th=1Put the puller in the tray of the container, connect the fingerbot to...

An automatic fish feeder. The pushing and pulling motion is achieved by this Bluetooth smart fingerbot https://www.amazon.com/dp/B0B97G3B8G?ref=ppx_yo2ov_dt_b_product_details&th=1 Put the puller in the tray of the container, connect the fingerbot...

This is an automated fish feeder equipped with a powerful magnetic holder, which relies on a Neodymium magnet for secure attachment. ...The feeder itself utilizes a Digispark Attiny85 microcontroller for precise control over feeding operations.

I took the automatic fish feeder that pefozzy created (thank you!) and tweaked it a little to fit the components I had on hand. Specifically a NANO arduino and a 9g micro servo (SG90). I also added a cap for the food bowl. The design is still a work...

I tried several of the other automatic fish feeders listed online, and didn't have much luck, so I designed my own. It's designed to feed small food pellets, such as the Top Fin Betta Bits shown in the photos. The feeder arm contains a circular hole...

I took the automatic fish feeder that pefozzy created and customized it to fit the components I had available. Specifically, I used a NANO arduino and a 9g micro servo (SG90). I also added a cap for the food bowl. The design is still a work in...

I took the automatic fish feeder that pefozzy created (thank you!) and tweaked it a little to fit the components I had on hand. Specifically, a NANO Arduino and a 9g micro servo (SG90) were used. Additionally, a cap for the food bowl was added. The...

This is a simple automatic fish feeder built using some cheap components I originally had lying around from previous projects. The design works well with food pellets, but feel free to try it with other forms of food. The feeder should be a perfect...

This is an auto-feeder designed for aquarium fish, driven by a stepper motor. The perforated disc rotates, capturing food through its holes and dispensing it via the bottom opening. A brown lip prevents food from falling through the perforations.

Automatic fish feeder remixed from coberdas and UrbanAtWork. Everything was designed in Fusion360. You can access the design here: (http://a360.co/2BmqVjW). It is centered around a Nema17 stepper motor. I used this one...

The automatic fish feeder dispenser was inspired by a great design on Thingiverse, but after printing I found it to be too big so I optimized it for size while maintaining functionality. The servo rotates at 45 degrees, with driving and programming...

Made this adjustable fish feeder for my 5 gallon tank. The slider and base may need a bit of sanding to slide with a little bit of resistance. ... PARTS REQUIRED: 1 x Clock...

Simply design and print a protective housing for your Arduino board, craft a timing mechanism through coding, and then create and assemble a fish feeder using your 3D printer. ...To complete this project, you'll also need to add a standard servo motor,...