eisel frame stand 3d models

It's a very nice frame stand. ...I recommend put termal glue on the bottom.

It's a very nice frame stand. ...I recommend put termal glue on the bottom.

Simple stand for frame, book or whatever else with same shape.

Made a frame then needed something to stand it up so.... ...back to design - a stand that perfectly fits my picture frame found here :https://www.prusaprinters.org/prints/118143-picture-frame-100-mm-x-125-mm   

Big and strong frame stand. Made for a very heavy glass photo frame that was 30x20cm. I recommend you to resize proportionally to your frame height and reduce infill if your frame is not very heavy. You can print one and put it in one side of the...

This is a picture frame holder to stand frames which are originally designed to hang on the wall. Can also be used for a tablet. Ich habe hier einen Halter/Ständer für einen Bilderrahmen ohne Standfuß erstellt. Kann auch als für ein Tablet benutzt...

Box Pen stand Frame. ...

Stand under the frame

Stand to replace broken picture frame

The 4 stand for YU Frame from taobao

A stand for pictures or digital picture frames. ...Also suitable for books or other items to stand on.

Needed some portable frame stands for an art display. ...Easy to assemble / disassemble to transport.

it's a stand holder for frames... ...it holds things at an 80degree angle

... sized picture frame. ...Made from two pieces the top simply pushes on to the main stand piece and acts as a backstop for the frame to rest against. Just rest your picture frame on the stand for a perfect viewing angle :-) (picture frame not included !)

Wanted to put a picture frame on my shelf with another in front without blocking the image, so made a stand. ... I use 2 for each frame.

Made these to keep my similar photo frames standing at the same angle so they'd all look uniform.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=60746 Instructions Using the following options: frame_lip = 8 frame_depth = 7 frame_width = 15 stand = yes stand_tilt = 15 frame_thickness = 15 picture_width = 180 picture_height = 100

... we have, so I whipped this up quickly. ...The two "seats" for the picture frame are 18mm wide. Overall it is 200mm wide x 100mm deep x 150mm high. The picture frame on the stand in the pictures is 13in wide x 0.6in deep x 16in high (330x15x406mm).

I bought a frame where the uprights and horizontals had a square cross section and made a stand of two feet connected with a wooden dowel. But the dowel is not necessary. ... This is a customizer so you can measure your frame and adjust the dimensions...

I needed to scale down the foldable picture frame stand, the holes were too small once scaled down. My solution is to replace the hinge with a preassembled hinge that comes out of the printer without assembly needed and seems to stay together...

I downloaded and printed [fotofreak58's 4x6 photo frame](https://www.thingiverse.com/thing:5247439) but I wanted it to stand instead of hang The first file is the one I printed but the part needed a little tape around the disk to snug the leg in the...

A photo frame stand. Easy print and you can scale it to suit a bigger or smaller photo. Picture frame shown is 225mm X 225mm by 15mm. ...This one printed in PLA 0.1 or 0.15 mm layers and 1.2 mm walls.

this is a simple painting/picture frame stand that can be used on a table. the part was printed using Black PLA with 0.2mm layer thickness. ... the simplicity of design allows 2 of these parts to be used for any size painting frame.

A photo frame stand. Easy print and you can scale it to suit a bigger or smaller photo. Picture frame shown is 225mm X 225mm by 15mm. ...This one printed in PLA 0.1 or 0.15 mm layers and 1.2 mm walls.

This was designed to fit a snare drums stand to hold a frame drum for ease of play. I used a Dixon concert snare drum stand to design the opening. Print 3 and then add some foam weather stripping from the hardware store. This has been tested. ...

Easy to assemble stand for a 4”x6” photo frame.Having a few homemade ¾” hardwood photo frames for 4”x6” photos, it was only natural to come up with a sturdy stand for them. Hopefully these will work for you. The stand’s back is around 6” tall and can...

Other Required items -D33 Pole x2 -3x15mm Aluminum frame -M3 bolt and nut -D6 x 3m magnet -M3 washer react to magnets -Glue A level tool is useful when assembling the pole and frame. Glue the washer to the adapter. Press the magnet into the clip...

For more of my designs check out my website: https://3domcontact.wixsite.com/3dom This is a replacement stand for a picture frame. The one supplied was basically a cardboard part that failed at the hinge (no surprise there). I roughed up the...

This quick little design allowed us to put the Angel Moroni on this stand and mount it to the picture frame's upper right corner. We attached it to their picture frame with double sided tape on both inside walls. ... Thanks @JP1 for such an awesome...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58508 Instructions Using the following options: parts = second slit = 4 frames = 8 stand_height = 75 height = 55.7 diameter = 120 width = 38.8 set_diameter = 0