electronic cigarette holder 3d models

atomizer electronic cigaretter holder

Electronic cigarette holder

Hello, Here is an electronic cigarette holder of my creation. It allows to easily recharge his device with the port below. If you want messure support contact me! For an electronic cigarette up to 23 mm wide and 35 mm deep. Bonjour, Voici un...

Hello,Here is an electronic cigarette holder of my creation.It allows to easily recharge his device with the port below.If you want messure support contact me! For an electronic cigarette up to 23 mm wide and 35 mm deep. Bonjour,Voici un support...

This is an holder for keep an electronic cigarette in vertical position for keep the flux in the lower side of the reservoir

Wall holder for electronic cigarette. I have ProVari so default settings customized for it. But design can be changed for other similar device. ... Instructions Can be printed without support.

... of hearing my wife's cigarette fall every time she put it down. ...So I created this holder that keeps the cigarette upright. Suitable for a 22 mm diameter cigarette, and at the same time it can be recharged. ... Pause printing for filament change.

Support of the cigarette during its reloading with passage of the USB wire Clipper on glass table of 10 mm thick

This holder can store a standard e-cig stick type, with room to store 2 bottles of liquid.

This holds my current assortment of electronic cigarettes and accessories. It's printed in old skool Icicle Blue PLA w/ 3 shells and 90% infill of water with red food coloring.https://www.youtube.com/watch?v=nciwf_8axos ...

I have made a modular cigarette holder. This fits the Atomizer of SmockTech tfv4 (23mm) as well as tfv8 (26mm). There is also the possebility to store batteries (eg, 18650). The construction works like a puzzle. The parts are marked with numbers:...

... http://www.thingiverse.com/thing:282761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=282761 Instructions Using the following options: holes_diameter = 3 holder_length = 54 wall_thikness = 1 cigarete_diameter = 14

... http://www.thingiverse.com/thing:282761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=282761 Instructions Using the following options: holder_length = 70 wall_thikness = 1 cigarete_diameter = 22 holes_diameter = 4

... http://www.thingiverse.com/thing:282761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=282761 Instructions Using the following options: cigarete_diameter = 16 wall_thikness = 1 holes_diameter = 4 holder_length = 75

Customized version of http://www.thingiverse.com/thing:282761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=282761

Customized version of http://www.thingiverse.com/thing:282761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=282761

for dorm friend

Stable support for 3 25mm (or 22mm) tanks. ...Of course, at least one tank of more than 25mm can be used.

This are two different holders for the e-cigarette joyetech eCom Supreme

for hold verticaly electronic vapor e-cig eGo style I made a slight tightening inside the object to hold it securely in order to vapoter beside his keyboard computer and put his cigarette at leisure ======================================== pour...

Electronic cigarette and liquid holder, designed to be printed in Cura's vase mode (Spiraliform). With a 0.4 nozzle set the layer height to 0.25 and the line thickness to 1 mm, you can do it safely and you will get the resistant model with a fast...

Holder electronic cigarette vaping atomizer Support cigarette électronique - Atomiseur Strada If you have many atomisers it's not good to lay them on the side, because the liquid could run out and starts rolling off the table very often. An...

Keep your electronic cigarette (made for joyetech ego-c, might fit others), Wacom stylus, or Sharpie close at hand with this weighted holder. Print both halves, fill with something heavy, then snap it together and put it on your desk! Inventor part...

Keep your Atomisers and E-Liquid bottles neat and tidy! ...5 x 14.8mm holes 4 x 24mm holes

... a caldo. ... Posizionare nel piccolo vano vicino al freno a mano. renault clio 4 car holder for kiwi electronic cigarette with powerbank and charging cable passage to be fixed with hot glue. ... Place in the small compartment near the handbrake.

This electronic cigarette head holder diameter 25

Electronic cigarette holder Innokin Zenith

Electronic cigarette holder, glue or screw the slide to the desired location, car, wall, desk, etc. ... very convenient. Can be resized or modified according to your e-cigarette. ... made with Tinkercad

Door electronic cigarette holder. Universal mounting with holding screw. For 1 E-cigarette + 2 vials. Plan on request by message according to your cigarette model. ...Plan available for download 1 day after request with possibility of modification...

Electronic Cigarette