elegoo mars endstop spacer for wham bam flexible build plate by 3d models

The Jupiter does not technically need an extension for the z limit switch with the XTR, but the springs are nearly fully compressed without one, and I did not like the amount of pressure I had to use to level the plate. I feared all that spring...

A Z limit spacer for the Anycubic Photon S to be used with the [Wham Bam FBS System](https://whambamsystems.com/fbs-for-resin) Spacer height is 2.6mm as recommended by Wham Bam print in your favorite material and install and remember to re-level your...

this is a distancer for the Mars V2P to raise the Z limit activator to compensate for the 2.6mm of added thickness from the Wham Bam Flexible Build System. Its a simple flat print with FDM or resin. No supports. You may need longer screws M3 8-10mm...

this is a distancer for the Mars V2P to raise the Z limit activator to compensate for the 2.6mm of added thickness from the Wham Bam Flexible Build System. Its a simple flat print with FDM or resin. No supports. You may need longer screws M3...

This replacement build plate knob is specifically designed for the Elegoo Mars, and it's a crucial component for the Z height increase mod. The new knob is 3 mm thinner than the original and features a hole in its center to alleviate FEP pressure...

... can see it in the photos here. just print out, use a drop of super glue if needed and push into place. then, with Wham Bam Flexible Build System installed, loosen your head screws, home over a sheet of paper then tighten back up for a perfect fit.

Adjustable BL Touch mount for Mobile Plate Mutant By Wham Bam Systerms

Just another unassuming platform for assembling new creations.

BMG DDR slim version interface plate for Mutant System by Wham Bam Systems.

interface plate for Creality Ender 3 Wham Bam Mutant System

Add 2.5mm to your Z limit in order to fit the new Flexible Build System for Resin (FBSR)! The124mm x 70mm system perfectly fits the Kudo Bean as well as the Phrozen Sonic Mini, and the Longer Orange 30. The added thickness of the magnet and the...

Although not required the spacer extends the intercepter arm about 3.8 mm XTR or 2.6 mm for FBSR to alleviate downward for or the screen by the build head springs. print in its side at .2 layer height. on fdm can also be printer in resin. ...

I made a custom MARS build plate holder for my dunk tank and it works amazingly well with this new method of cleaning. Check out the video on how to make your own dunk tank here: https://youtu.be/RL3f0rw0NGI If you're interested in trying this out,...

Download Spacer for Uniz IBEE created by Hrvoje for the Wham Bam System FBSR.

This is a solid Dummy file of the Wham Bam Systems MUTANT that can be used for design purposes to create specialized mobile mounts. Included are both STL and STEP Files. Design copyright and patent Wham Bam Systems. ...

This is an interface plate created for the Micro Swiss NG for use with the Wham Bam MUTANT V2. printed at 0.2 layer height. You will need 5 x 3 mm threaded inserts that come with the MUTANT kit Two versions available. Version A: Allows...

... the new screws to the bed like shown in the photos, nice and tight, then attach the plastic parts with another lock nut and washer. One precision: I mounted my Wham Bam system directly onto the heated bed, discarding the aluminum plate entirely.

One precision, I mounted my Wham Bam system directly to the heated bed and discarded the aluminum plate. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Coex3d ABS Or PETG ...

simple Vat Stand or Drip Stand for resin build plates like elegoo mars works well

Anycubic Photon Mono SE SPACER - Wham Bam + Two Trees Flex Plate Spacer Part for Endstop after adding the new magnetic BUILT Plate Here 3 Parts for : - Wham Bam 3,00 mm - Two Trees 2,75 mm (Ali Express) - No Namer 2,50 mm Print in PETG You need to...

Here is a simple design for a shorter build plate knob for the Elegoo Mars 3D printer. If you've done the increased Z height mod to achieve 170mm in height, the knob will collide with the enclosure at its top end. This solution prevents that issue...

This is a revised version of Peter Solomon's Elegoo Mars Build Plate Angled Holder. The handle has been relocated from 90° to 45° to facilitate better drop formation. I advise using PLA, as it is resistant to IPA. Two versions are available: one...

I also replaced their logo with the Elegoo "e" on the front of the build plate as I think it fits better with the machine's design. I printed it on my Ender 3, flipped upside-down with supports and it works fine, although on my original Mars the...

The build plate now has an angled corner, which allows for better resin drainage during the printing process. Additionally, I've trimmed the design slightly to ensure a snug fit on the Mars build plate. ... This redesign still utilizes the same screws...

This is a remix of Peter Solomon Elegoo Mars Build Plate Angled Holder. The handle is re-positioned from 90° to 45° to ensure better drop formation. I recommend using PLA because it is IPA resistent. I added 2 version right- and left-hander. Update:...

Mars Onboard Build Plate Dripper While I like the idea of the Mars supplied device for leaning your build plate while dripping clean, it takes two hands and you need a place to keep it when out of service. So I made this! this file is free to you,...

Mars Onboard Build Plate Dripper I like the idea of Mars' supplied device for leaning your build plate while dripping clean, but it requires two hands and takes up valuable space when not in use. So I created this! This file is free to you; all I...

I'm relatively new to Eleegoo Mars Pro since February 2020, and I had a tough time printing the Build Plate Angled Holder because I couldn't figure out how to use the support correctly. So, I decided to create my own version that I can print flat...

This is a version of my regular Mars 3 build plate holder that uses a magnetic mount instead of the 2020 extrusion mount.  Compatible MachinesMars 3Mars 2/2 Pro (Im 95% certain its the same mount as the 3, but I am awaiting...

... end and scrape the prints off with ease. This might work for other Mars machines, I have not been able to test it. Printer Settings:.2mm layer height20% infill3D Solutech Premium Black PLA (PETG might be better, but PLA is holding up just fine)