elegoo neptune 2s 3d models

I have two Elegoo Neptune 2s side by side and needed to redirect the draft from the psu from one on the left away from the one on the right and back wasn't an option either so i made this one.Prints easily with organic supports to hold up the screw...

Some simple adjustable feet, inspired by need and other designers. ... This object was made in Tinkercad.

This is a small filament guide that mounts on top of the filament detector / feed to prevent wear to the brass inlet of the feed. ... If you want to use the screws, you'll need to replace the originals with M3 x 35mm screws, otherwise, double sided...

this is for the Elegoo Neptune 2/2s printers. ...it will hold a LED light strip on the top gantry.print at least 2

I wanted to clean up the Z-axis wires on my Neptune 2S, they've touched the table and lead screw during a print before. This cable cover has a nice pressure fit, but also the filament detector screws can be used to fasten it. I use it together with a...

Mainboardcover for better Airflow an more quieter operation Udes Materials: Fan https://www.amazon.de/gp/product/B087JHB9BV/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 Epoxy ...

I had looked and downloaded lots of different filament guides but, none that i could find worked well with a side mounted spool, hence this thing was created. This object was made in Tinkercad. ...

This is a simple filament guide i made because the filament scratched against the hole of the extruder. ...This resulted in an anoying squeaking while retracting and extruding.

This is a nice short stubby filament guide that will fit Bowden tube through it to make it nice and smooth as well as stop that annoying 'squeak' that the Neptune2S makes through the filament sensor.I shall possibly make a more slimmed down\simple...

Fan mount for facilitating Noctua 40mm hotend and filament cooler using two fans.

Modified Hero Me Gen5 Gantry Adapter Plate for use on the Elegoo Neptune 2S printer. ... Affix to plate using two screws through holes on upper tabs and the two screws through hot end mounting holes.

This is a direct drive mount for the Elegoo Neptune 2S with the stock extruder. ... If you have a BMG extruder, see https://www.thingiverse.com/thing:6219861

Now the tool holder stays on tightly and I have found that it is very handy for the main tools needed for an Elegoo Neptune 3d Printer, so thanks to Penguinman96 and DantRush for your original tool holder blueprints. Resolution - 0.2 Infill - 20 ...

... The models are made with the 3D models from Elegoo (http://69.195.111.207/tutorial-download/?t=FDM_Neptune2_and_2D_Source_File_Date) as reference. A print of the front has been made but due to bad adhesion, are there no good pictures to show.

I am using this plate / fan duct on 6 of my Elegoo Neptune 2S printers currently (will post additional pictures). [ Update: 02.11.2022 ] Added a compatible BLTouch plate, "en2bltouchfangplate", to the collection. I may combine plates in the...

Ich habe hier mal einen BMG Clone Direct Drive Umbau für den Elegoo Neptune 2 / 2S gebastelt. Er funktioniert einwandfrei bisher und läuft bei mir schon unzählige Stunden. Ich hab mal ein Foto angefügt wie es gedruckt habe (mit Support...

This is a side mount adapter for the factory Elegoo Neptune 2 / 2S spool holder. The adapter reuses the M4 x 8mm bolts and M4 t-nuts to bolt to the 4040 extrusion frame and requires an extra set of M4 x 8 mm bolts and M4 nuts for the spool holder....

This is a filament sensor hat for the Elegoo Neptune 2 / 2S. I wanted to use a PTFE tube to align filament going into the runout sensor while ensuring it stayed in place during extrusion and retraction. Simply use a PC4-M10 pneumatic fitting to...

I also have a (low profile) or smaller version that will be in my profile.Link to low profile version:https://www.printables.com/model/324158-elegoo-neptune-2-2s-2d-3-filament-guide-low-profilPrint SettingsPrinter Brand:ElegooPrinter: Neptune...

For this project, your gonna need a elegoo neptune 2 or 2S and a E3D Hemera (full kit) print the part and detach the gear mechanism from the stepper motor on the hemera with 4 screws, mount the hemera to the adaptor mount the hemera to the hotend...

I also have a (low profile) or smaller version, that is not as big and bulky.Link to low profile version:https://www.printables.com/model/324158-elegoo-neptune-2-2s-2d-3-filament-guide-low-profilMake sure to go check out all of my other Elegoo...

This is the new dual 5015 Satsana model adjusted to fit on the Elegoo Neptune 2/2S printer. Please refer to the original thing (https://www.thingiverse.com/thing:5750189) for installation instructions and adjust them according to the following...

This is a mount for installing dual Voron M4 extruders on an Elegoo Neptune 2 / 2S/ 2D, it mounts to the top of the frame between the 2 spool holders and has a mounting solution for both of the run-out sensors.Print the main body and 2 copies of the...

i create to thing for change the board and Display to BTT SKR Mini E3 V2 and BTT TFT 35 E3 V3 The cover is open , i have 2 Fan in The IKEA LACK colling the electronic

A barebones mounting bracket to relocate the printer's touchscreen display so that it can be used with the printer facing sideways and without the bed getting in the way. The screw holes are sized to fit some random spare screws I had. ...I've included...

Rechargeable Parkside (from Lidl) with adjustable light intensity holders. ...

This is a cam support, to fix the cam in front, it can be easily removed in 1 second, the center distance of the cam is 16 mm, my cam is a webcam that works with the "agent UI" software to follow the remote progress on android, rack for store in

Certainly! The printable remix model featured in this video serves as a game-changer for 3D printing enthusiasts. This model allows users to seamlessly attach a direct drive mount to their extruder, enhancing the overall printing experience. The...

For this project, your gonna need a elegoo neptune 2 or 2S and a E3D Hemera (full kit) print the part and detach the gear mechanism from the stepper motor on the hemera with 4 screws, mount the hemera to the adaptor mount the hemera to the hotend...

This is an Add on for the Elegoo Neptune 2 and 2S. One File is the Holder for the remote and the other file is for the print head. The support does not require any fixing, it clips perfectly, The button is fixed with 2 M3 screws. if you have...