elekslaser 3d models
64 3d models found related to elekslaser.thingiverse
I made some squares to be able to fix a base in my elekslaser. ...To fix it You can simply use M3 screews and T-thread Bosch nuts to join it to bosch profile.
thingiverse
Use this replacement bracket to stabilize your Elekslaser onto a wooden board. To set this up: 1. Print out 2 left brackets,2 right brackets and 4 bases. 2. Attach the brackets 3. Attach the bases to the brackets 4. Screw...
cults3d
Felt holder for ELEKSLASER A3 PRO Servo motor SG90 2 Axis Ø8x85mm 4 M3 screws 2 M5 screws 2 Nuts M5 2 LM8UU Ball Bearings 1 Elastic band
thingiverse
I have created this to make my "EleksLaser A3 Pro" higher. It helps to Laser bigger objects. I glued the original rubber feet under the printed ones. ...
cults3d
Felt holder for ELEKSLASER A3 PRO (version with more powerful servo motor.) Servo motor MG995 2 Axis Ø8x85mm 4 M3 screws 2 M5 screws 2 Nuts M5 2 LM8UU Ball Bearings 1 Elastic band
myminifactory
Support feutre pour ELEKSLASER A3 PRO(version avec servo moteur plus puissant.) Servo moteur MG9952 Axe Ø8x85mm4 Vis M32 Vis M52 Ecrous M52 Paliers à billes LM8UU1 ÉlastiquePARAMÈTRES D'IMPRESSION 3DPETG ou PLAcouche: 0.20mmremplissage: 20%
thingiverse
Custom removable snap-fit stand for EleksLaser A3 Pro - Store in an upright position to save some space! :) Mount the Y axis stoppers so that they touch the front acrylic parts (see photos). They hold most of the weight of the frame. ALWAYS...
cults3d
Elekslaser Z axis upgrade made with my CNC and 3d printer. Now I can rapidly adjust the height with a stroke of 125mm, obtaining a more precise focus too. Guide Rods: Ø8,0 mm Linear Bearings. ...LM8UU Lead Screw: M8 Bearings: 608Z 22.06.2019: Added...
thingiverse
Elekslaser Z axis upgrade made with my CNC and 3d printer. Now I can rapidly adjust the height with a stroke of 125mm, obtaining a more precise focus too. Guide Rods: Ø8,0 mm Linear Bearings. ...LM8UU Lead Screw: M8 Bearings: 608Z 22.06.2019:...
thingiverse
I spliced longer cables onto the elekslaser after adding the z-axis attachment. To control the extra cabling length I: 1. Attached a ~6 inch stick to the end of the cable bundle using the cable sheath 2. Attached the 3d-printed...
thingiverse
A simple bracket to mount the Elekslaser A3/Pro laser engraving unit to a board so it doesn't burn your surfaces and keep the frame square. I secured the elekslaser A3 onto a sheet of 18mm MDF I had sitting around using 3.5x20 screws. It will...
thingiverse
This attachment holds an eleks laser onto a z-axis attachment. ... Note: If you are trying to use a laser with a z-axis attachment you will need to get a software like T2laser. The elekslaser software doesn't have that capability as of 7/5/2020.
thingiverse
A simple power button for the Elekslaser A3 Mana SE board "case" that comes with the unit. ... I had to use an old pencil to stick through the hole and press the power button which was a pain, this just drops into the hole and sits on top of the...
thingiverse
I have an EleksLaser A3 Pro and I do not use it all the time so I made this simple clip to hold it up on the wall out of the way when I am not using it. I thought it was useful and figured I would share it with the world. If you down load it and use...
thingiverse
EleksMaker EleksLaser Pimoroni Pibow mount =================================== Like a lot of people with these machines I use LaserWeb running on a Raspberry Pi to control it. In order to tidily mount the Raspberry Pi, I slid a couple of spare...
cults3d
replacement belt tensioners for the EleksMaker EleksLaser A3 Pro Laser Engraver. ...They work better than the original ones ;).
thingiverse
replacement belt tensioners for the EleksMaker EleksLaser A3 Pro Laser Engraver. ...They work better than the original ones ;).
thingiverse
I wanted to use the Elekslaser belt tensor by joshuruiz, but I didn't have any extra M3 bolts or nuts; I only had what came with the kit. ... So I re-designed this to use only the M5 and M3 bolts/nuts that the kit belt clamp uses.
cults3d
I had an old EleksLaser at home and after I repaired and improved it with carriage tensioners (https://www.thingiverse.com/thing:3422982) and a cable chain (https://www.thingiverse.com/thing:2765001) i thought I am going to build a draw module with...
thingiverse
I had an old EleksLaser at home and after I repaired and improved it with carriage tensioners (https://www.thingiverse.com/thing:3422982) and a cable chain (https://www.thingiverse.com/thing:2765001) i thought I am going to build a draw module with...
prusaprinters
I have an EleksLaser A3 Pro and I do not use it all the time so I made this simple clip to hold it up on the wall out of the way when I am not using it. I thought it was useful and figured I would share it with the world. If you down load it and use...
thingiverse
EleksMaker EleksLaser air assist 80mm fan mount ===================================== I wanted an air assist on my EleksMaker EleksLaser engraver but didn't have any 40mm fans available, so decided to re-use one of the many 80mm fans I had. The...
thingiverse
I have an older style EleksLaser A3 Pro laser engraver and wanted to share all the upgrades I did. I have not verified these upgrades will work on the newest version of the A3 Pro but based on pictures they should. I have included .stl, .step &...
thingiverse
I didn't like any mounting options, so i made my own solution. This option requires a couple of M5 nuts and bolts. ...Cheers.
thingiverse
This is my focusing wheel. There are many like it, but this one is mine…. :D First version is for original lens with knurled ring and the second version for spare lens M9x0.5 thread. I hope they will fit perfect as they did in my case. ...
thingiverse
ventilation pour le laser eleksmaker a3 de 2.5w liste de matériels: -2vis m3x10 -4 vis m3x16 -2 ventilateurs 5015 12v -4 insert m3 5x5