emisar d4v2 vs fw3a 3d models

Pocket Case for a Emisar D4v2. ...Requires 8 3x3mm magnets.

I liked the design of this light hood but needed to adapt it to my LED light an Emisar D4v2. The cutouts allow for a 25mm ID O-ring to secure it in place. Lined with Tintape I design it to be Printed in Cura with the Hood set to have Fuzzy skin: ...

Transform your Emisar D4v2 flashlight into a fancy lantern! Do you like the BLF LT1 and want something smaller? This might be just right for you! Included in this kit are two parts (consisting of three models to print): - The **base** for a...

Transform your Emisar D4v2 flashlight into a fancy lantern! Do you like the BLF LT1 and want something smaller? This might be just right for you!</p><p>Included in this kit are two parts (consisting of three models to print):</p><ul><li>The...

ever want a gopro holder for your d4v2? now u can! ... put it on hemets, etc...

Designed to fit a 10mm diameter x 4mm tall neodymium magnet and a 12mm ID x 20mm OD fiber washer (anti-scratch). ... A convenient way to hang a D4V2 flashlight equipped with a tailcap magnet.

This is a scale model of the D4V2, as accurate as my calipers can measure and as detailed as I had the patience for. STEP and FCSTD files are also included.Print tail-down, with supports if you need the lanyard hole to come out perfect.Disclaimer: I...

This is a scale model of the D4V2, as accurate as my calipers can measure and as detailed as I had the patience for. STEP and FCSTD files are also included.Print tail-down, with supports if you need the lanyard hole to come out perfect.Disclaimer: I...

This is a scale model of the D4V2, as accurate as my calipers can measure and as detailed as I had the patience for. STEP and FCSTD files are also included. Print tail-down, with supports if you need the lanyard hole to come out perfect. ...

... to get the lid to snap into the body reliably.</p><p>I print these out of PETG using a 0.4mm nozzle with 0.2mm layer height. Try as many colors as you can!Make a glow-in-the-dark diffuser and set the D4V2 to lightning/beacon mode for maximum fun!

It has been specifically designed to house an Emisar D4 and Emisar D4v2 flashlight (sans pocket clip) but can accommodate any flashlight with a cylindrical portion 25 mm or smaller in diameter and 51 mm or larger in length. The mount works best with...

... a case for the Emisar D4. It holds either: a. The Emisar D4 Flashlight in 18650 configuration, an 18350 tube, and two 18350 batteries. b. The Emisar D4 Flashlight in 18350 configuration, an 18650 tube, one 18650 battery, and one 18350 battery.

Requires 4 - 3x3mm magnets for the lid and 1 - 3x20mm dowel rod for the hinge.

Small protective box for the flashing kit for Emisar and Noctigon flashlights sold by Hank Wang. Might require a bit of fitting on the USB connector's hole, I manually enlarged it a bit using a knife, made it slightly undersize so that the board...

Emisar D4V2 model with 18650 tube

This is a very basic model of the d4v2. ...I've printed it and the dimensions seem to match my real d4v2. This is mostly useful for designing things that work with the d4v2.

Stability Stand - friction fit stand for the D4 and FW3A to increase stability on uneven surfaces or when you want to avoid your lantern falling over. S2+ size lights work okay but do not sit snug in the base. 24mm S2+ Step Up Ring - an adapter...

Model of an Emisar D4V2 with installed 18350 tube.

Iron Man case for Emisar D4v2. ... Requires 3x20mm dowel pin for hinge and 4, 3x3mm magnets for lid

Holder for lumintop FW3A series of lights or any light with a 21.5mm OD Uses a 30mm x 3mm magnet

... screw on the tailcap again. (Depending on your printer accuracy you might have to tune the dimensions slightly. Print in 0.1 mm to get the right thickness.) Customize it! Use the filament color you like to add some nice highlight to your FW3A.

It is based on [my Noctigon KR4 Tactical Ring design](https://www.thingiverse.com/thing:4707744), but recreated with FreeCAD and adapted for the FW3A. Comes with lanyard hole as well! There are versions with one, two and three lobes. Print in...

This is a tactical ring for the famous FW3A (and similar lights using the same tailcap).It is based on my Noctigon KR4 Tactical Ring design, but recreated with FreeCAD and adapted for the FW3A.Comes with lanyard hole as well! There are versions with...

It is loosely based on my [FW3A Tactical Ring](https://www.thingiverse.com/thing:4900452), which is available with one, two or three lobes. Print in 0.1 mm to get the correct thickness. After printing I used a knife to smooth out the chamfer at...

This is am extremely simple, basic diffuser for the popular Lumintop FW3A flashlight. The FW3A has a 25.5mm head, and you should be able to scale it up or down accordingly to fit other lights. I designed this because I was so disappointed with...

Then you might want to try this lanyard ring!It replaces the original metal clip or lanyard ring of your flashlight.Remove head and tailcap from the battery tubeRemove clip and o-ring (it might fit without removing the o-ring, but there's a risk to...

I love my FW3A and I often use it to light whatever I'm working on, but that requires me to give up one hand for the flashlight.&nbsp;Well, I designed this to hold the flashlight for me in any position that I want.&nbsp;The design doesn't use any...

... ...Easily Accommodates Compact Flashlights like Emisar D4, FW3A Models. If this innovative clip proves useful to you, kindly consider a donation to my PayPal account at paypal.me. ...Your contribution will help offset the time invested in its design.

D4V2 Lantern diffuser - simple quick print, fits both ends, one for storage, other for lantern mode. ... I printed with a 0.6mm nozzle at 0.3 layer height but probably not fussy to smaller or larger layers