end carriage 3d models
147328 3d models found related to end carriage.grabcad
This end carriage designed for Gantry carnewith 2 wheel blocks 315 mm dia.
thingiverse
This carriage was inspired by the Hammerhead Delta Carriage, but I needed a carriage with 48 mm spacing. The holes are aligned to a MGN12H linear rail carriage. The holes for the steel balls are designed for M3 threads and the back side holds a M3...
thingiverse
The hot end carriage wheels clashed with the left-hand end (rear) plate of the X pulley and needed the limit switch offset. This in turn moves the hot end 5mm right and therefore reduces x-direction print area. To prevent wheel clash this bracket...
thingiverse
... ... It allows for changing parts and not having to completely disassemble the hot end carriage when you want to change things. I also tried to keep it as small as possible so that you can have part cooling and bl touch without losing any print area.
prusaprinters
It allows for changing parts and not having to completely disassemble the hot end carriage when you want to change things. ...I also tried to keep it as small as possible so that you can have part cooling and bl touch without losing any print area. The...
thingiverse
This is the part where the hot end (and the extruder if direct drive)sits
youmagine
Also this way I can use the common RoStock carriage so other parts can easily be fitted on (like my waterblock https://www.youmagine.com/designs/triple-water-block). ... Info on the arms can be found...
thingiverse
this is from another user l added logo and pipe https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a...
thingiverse
SN-04 sensor location is mounted to the fan duct beside hot end instead of where shown in the pics. X shaped bracket is for mounting the hot end board in a new location of your preference. ...X endstop is included to make sure the assembly doesn't crash...
thingiverse
Tronxy X5sa Pro hotend carriage plates, now you can modify them for direct drive without cutting the stock bracket, or convert them to dxf and have them laser cut etc etc etc Original Build Here...
thingiverse
A simple Bowden style extruder X carriage mount for a E3DV6 NOTE: On this design the baring shafts (8mm with LM8UU bearings) are in line (vertical) with the drive belt. To affix the belt to the unit use a spare strip of drive belt of about 40mm...
thingiverse
project cable management backplate mount for tronxy x5s the idea is: use the RJ45 for all the sensor, thermistor and fan cables the XT30 for HE-cartridge and you kinda get a quick release or hot swap carriage for a tidier look and less wear and tear...
thingiverse
This is the hot end carriage plate of my idea I haven't tested this yet, but I'm thinking it should work with stock parts. the plate should work at 4 mm thickness (increase it from the 2 mm as it is designed for a metal part.) this is a quick design...
thingiverse
This is a E3d Extruder mount. I printed it in low quality with 100% infill. The screw holes are undersized for a 3 mm screw, and the screw that goes behind the fan on the fan mount should be a flat head . ... I have been experimenting with rotating the...
grabcad
In order for the wheel flange to be positioned in the right direction, it is necessary to be bored by the boring machine at the same time, otherwise the wheels will be tilted and will cause the wheels to wear.
thingiverse
This allows you to replace the stock carriage assembly for a much lighter weight version with the bonus you can now fit an E3D V6 (or clone) hot-end. Additionally it adds a 5015 blower fan which on it's own is far more efficient and provides better...
thingiverse
... end can be purchased from Ali Express for about $12.00 USD. Get the fitted hot below Buy Here (J-Head Metal Hot End) -------------------------------------------------------------------------------------------------------------------------------
thingiverse
I remixed Blinkingsun's hot end mount to accept some of the existing part cooling fans on Thingiverse. This one specificially: https://www.thingiverse.com/thing:3446017 This should also fit: https://www.thingiverse.com/thing:3507515 Just removed...
thingiverse
This is a work in progress, I'm uploading now because people have asked for it and I don't have a lot of time to Finnish it. everything does work as is but could use some slight adjustment on the holes for the bltouch screws, though you can still get...
thingiverse
End Carriages The larger load-bearing holes are printed horizontally: expect to clean up artifacts from bridging and overhang sag if you print ABS at ~0.3mm layer heights. I use a drill bit to gently ream out the 8mm rod holes. This gives me a...
prusaprinters
I used 10mm M3-0.5 cap head screws for the bulk of the assembly, with 16mm screws and nuts for the X belt and [planned for] TR8 flanged nuts. End Carriages The larger load-bearing holes are printed horizontally: expect to clean up artifacts from...
thingiverse
Hot End Carriage: Removable carriage that doesn't affect the Z Probe. This design allows for quick swaps of hot ends, laser module, pen, etc. Carriages for the other items have not been designed as of yet. Materials: 1 x 30x30mm fan 2 x M5x60 bolt...
thingiverse
Prusa i3 x-end x-carriage by radus design x-end with clamps for better rods fix