ender 3 bowden tube 3d models
832462 3d models found related to ender 3 bowden tube.thingiverse
Ender 3 Bowden tube lock with zip ties Fixed version Improvements: - Corrected the tube lock size to fit the Bowden. - Aligned the fitting hole with bowden axis. - Strengthened the corners. ... Recommended zip ties size 2.5mm wide
thingiverse
Secures the coupling on the bowden tube for the Creality Ender 3.
cults3d
My first rookie design, nothing special, but works to support the bowden tube for the ender 3 Pro (and I suppose the Ender 3 regular version).
thingiverse
My first rookie design, nothing special, but works to support the bowden tube for the ender 3 Pro (and I suppose the Ender 3 regular version).
thingiverse
Modeled up a locking clamp for the bowden tube on my ender 3 pro. I printed off https://www.thingiverse.com/thing:3868796 this modified extruder upgrade and my bowden tube nut was looser than I would like it to be. I didn't feel like trying to fix...
prusaprinters
Modeled up a locking clamp for the bowden tube on my ender 3 pro. I printed off https://www.thingiverse.com/thing:3868796 this modified extruder upgrade and my bowden tube nut was looser than I would like it to be. I didn't feel like trying to fix...
thingiverse
This is a simple bowden tube / hotend cable clip, designed for my Creality Ender 3 (one of my first design projects). It should work for other printers with a 4 mm PTFE bowden tube as well. Installation may be tricky, I noticed that it works best...
thingiverse
Bowden Tube Lock Zip Ties, worked perfect and the tube is not moving now. ... Found so many on thingiverse but i did one which is more simple.
thingiverse
I designed my own bowden tube lock which uses one 3 mm width zip tie and it's rock solid (don't mind another zip tie on the photo). Fits almost every M6 connector with 8-8,1 mm diameter flange (part where is no thread) and if it's up to 14 mm long...
thingiverse
Must have been my zip ties but the tube kept getting pushed out. ... I cut the original model to get a 360 degree enclosure around the tube and lifted the center face on one side .4mm to apply more tension.
thingiverse
Mounts on the end of the top rail of Ender 3 or similar V rail Mendel style printers, providing a filament guide for rear/side mounted spool holders into a bowden tube. I am using it with this spool holder mount...
thingiverse
Remix with holder for the bowden tube and cables, made the screw hole tighter and extended the frame to remove wiggle room.
thingiverse
Since I using drybox and needed to feed from the left, so I designed a Bowden tube filament guide. It can prevent friction between the filament and the extruder/Z Axis, and reducing the area exposed to moist air. ... * With M6 thread, M6...
prusaprinters
Since I using drybox and needed to feed from the left, so I designed a Bowden tube filament guide.It can prevent friction between the filament and the extruder/Z Axis, and reducing the area exposed to moist air.* With M6 thread, M6 Fittings(I'm using...
thingiverse
This is a bowden tube holder for an Ender 3 (or pro) with a Microswiss all-metal hotend and the Hero Me Gen 5 Note**: I integrated this into the gantry adapter and it works much better: https://www.thingiverse.com/thing:4862969
thingiverse
... upgrading to Capricorn Tubing and aftermarket push fitting from Amazon. ...this clamps onto the aftermarket fitting and then locks the tube so there is absolutely no movement whatsoever. Fits 4mm Bowden Tube push in fittings with a 10.75mm collar.
thingiverse
I just wanted a simple Bowden tube holder for my Ender 3 S1 Pro, so I could have a second filament on the ready. Using an m3 x 16 screw to attach to the existing spool holder. ...
thingiverse
I used the idea that bowder tube springs. It is the best idea for filament guide. What I didn't like in the original design, that you can't just put it on if you have something on the top of the Z axis (bearing, knob). So my version you can put...
thingiverse
Necessary to stop flex at the bowden tube push fit union, as the flex was causing the joint to eventually fail. So far so good. I have included the .f3d and .step files for those who like to remix or adapt. There is one M3 screw and nut, and...
thingiverse
You will need 1 M6 and 1 M10 Bowden connectors and PTFE tube 4mm OD.
thingiverse
Bowden tube holder for the Palette 3/pro to mount its attachment on the Ender 3.
thingiverse
Use 2 zip ties to secure your bowden tube and cables to make sure they stay vertical, minimizing damage to the cables and reducing any risk of the bowden tube coming loose or wearing out prematurely. The support clips into place, it may need a...
thingiverse
### **This now lives on [Printables](https://www.printables.com/model/347665-ender-3-v2-filament-guide-with-bowden-tube-support) and may not be up to date on Thingiverse** None of the existing filament guides I found were quite what I needed so I...
thingiverse
...... It also work for Ender 3 / Ender 3 Pro / any printer that use PC4-M6 The reason why I made this remix is because I own bad quality filament. Thus the "Insert part" always cracked (four times!) even though I already made it bigger than the original.
thingiverse
... was stuck. ... In the process, I broke my Bowden tube insertion clip. So I needed a new one. It might not be perfect but it fixed my problem. ... The print takes about 10 minutes with a layer height of 0.1mm and costs 0.08m of filament.
thingiverse
3. Put Cura in "custom mode". 4. Select the filament guide, and use the button "per object settings" on the left side. 5. Select "Infill Mesh" (now called: "Modify settings for infill of other models") and enable that setting. 6. The filament...
prusaprinters
Guides your filament to the extruder using a piece of PTFE bowden tube. This version doesn't need the adapter, but just holds the tube press-fit.For best results, use TPU. ...It'll hold the tube snugly, and flex to get just the right angle between your...
thingiverse
This simple part allows a bowden tube to guide the filament as it feeds into the printer. This pairs very nicely with a filament drybox if you have one available; it can also be used to reduce strain on filament as it feeds from your normal spool. ...
thingiverse
Remixed the Ender 3 pro filament runout sensor by blaiseb with slot for bowden tube.
thingiverse
... as well. The side mount itself was a remix from this design: https://www.thingiverse.com/thing:2917932 Printer: Ender 3 V2 Support: Non on the main piece, with tree support on the top side mount. ... Infill 25% (this could likely be 10% or less)