ender 3 filament guide 3d models

This is a remix of: https://www.thingiverse.com/thing:3819008 That endclip didn't quite cut it, but it was the best I could find on Thingiverse - still, it lacked proper long attachment, making its weak point the surrounding screw hole. ...To give it...

I'm ready to assist you! Go ahead and provide the original text. ...I'll rewrite it while following the rules you specified.

The original concept is a stroke of genius, yet I found the supporting framework lacking in some areas. Fortunately, addressing this issue is simplicity itself. ...A nod of appreciation is owed to the creative force behind the initial remix - my...

This is a DIY project I put together utilizing my trusty old extruder wheel. ...All it requires is an M4 screw and a matching nut to get up and running.

updated this thing file wth a tube that goes up and will not brake that easy

Remix of other two designs as I didnt want to use the screws. ...Quite tight fit but it does fit and hold.

Sliced the original to fit around the Z-rod rather than having to slide it completely over any z-rod restraints that a person might have. This just makes it a bit easier on replacement later (as it is arguably a wear item). ... Category: 3D Printer...

I had accumulated a surplus of extra 606zz bearings from another endeavor, so I recreated the mount and wheel for use with this bearing. ... Update: I added a longer cover for the wheel to accommodate the slightly bigger wheel made, and reduced the...

Humans typically opt for high-quality 22x8x7 ball-bearings that deliver consistent performance and reliability.

requires two longer M screws to replace the two already on the top securing the top horizontal extrusion (I used 45mm long). Doesn't need to be too strong as not supporting any weight other than itself although might want to be printed in petg if...

This one's a bit trickier to get right on the printer, so try matching the original one as closely as possible. Once it's in place, you can forget about making any adjustments - and feel free to use those original screws! ...It's printed with PETG...

Carefully rotate all components before assembly to ensure proper alignment. When installing, exercise caution to avoid moving the z-axis support and losing any screws or washers. Print on high-quality settings, using a layer height of 0.1mm for...

The opening is a scant 4 millimeters.

I rejected the original design's rounded features, deeming them juvenile and overly playful. ...Instead, I opted to reimagine the concept in an industrial aesthetic, leveraging a cantilevered design to convey a sense of strength and modernity.

Same as the original but for a 6901 bearing.

Lowered the roller to allow using https://www.thingiverse.com/thing:190118 The original also kept getting pulled out of the 4040 extrusion, so I made a bracket with T nuts to re-inforce it. ... I did not test the version attached here

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

A remix between two different designs. ... For the arm I have used https://www.thingiverse.com/thing:2917932 For the Dust filter head I have used https://www.thingiverse.com/thing:4971024 Good Luck!

I carefully positioned the model onto the extruder.

This is a lighter/slimmer version of the arm that snaps on to the same End_clip.STL Refer to original file here: https://www.thingiverse.com/thing:2917932

The pioneering robot. ...Utilize this initial prototype.

Had a bunch of extra 606zz bearings from another project, so recreated the mount and wheel for use of this bearing. ... Update: added a longer cover for the wheel to accommodate the sightly bigger wheel made, and lessened the diameter of the hole to...

A remix of ne0tec's version https://www.thingiverse.com/thing:4922036, which is a remix from the original file uploaded by Jonasen here https://www.thingiverse.com/thing:2894097

The base alwayse about to come out so i make it longer, go download the arm in the original post of Filboyt https://www.thingiverse.com/thing:2917932

Alternative Axle for Ender 3 filament guides: https://www.thingiverse.com/thing:3030708 so the spindle doesn't come off during printing. ...

Ender 3 / Ender 3 Pro Filament Guide Rod System A crucial component of the Ender 3 and Ender 3 Pro 3D printers, the filament guide rod system consists of four essential parts: two metal rods with a V-groove, one top plate, and one bottom plate.

Alternative Axle for Ender 3 filament guides: https://www.thingiverse.com/thing:3030708 so the spindle doesn't come off during printing. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Category: 3D Printer...

This is remix of " Ender 3 Filament Guide by Filboyt" with different "end clip", I've just changed the end clip so its easier to mount and for it to hold better

Improved Version 3 Better Filament Alignment Closer to the Z Rod The Bearing Remains Original, a High-Quality Ender Extruder Bearing Measuring 13x4x4 in Size A Robust Fastener is Used, Specifically a Bold M4x16mm Countersunk Screw