ender 3 filament guide 3d models

Create a filament guide for your Ender3 or other Creality bowden printer by gathering an old PTFE tube, approximately 20cm in length - feel free to use a longer or shorter piece if needed. You will also require stock M3 bolts with a 4mm hole...

Since i changed the extruder kit to a dual drive gear due to damage caused to the stock one, i used the stock kit roll bearing to design a filament guide. Required material: roll bearing, 3mm*12mm wood screw . ... Dual drive gear extruder kit:...

Remix of https://www.thingiverse.com/thing:3428924: arm that goes to the back of the printer is extended by 2 cm so the roller is more in the center of the spool. ...Ender 3 logo removed to shorten print time.

Version 3 Offers Optimized Performance with No Ring Print Issues at Any Resolution. If Your Printer Struggles to Bridge, Print End Clip with Support Lines at 1.8mm Apart (5 Total Under Roof) Only Touching Build Plate. The End Clip Has Been...

To ensure a precise fit, I resized the bearing guide stem and wheel, so users will likely need to use sandpaper to create a seamless connection. The updated design is optimized to prevent filament slipping and pinching issues. As a newcomer to the...

I like Ballisticdoug's take on the existing design. ...I added slots for easier assembly and made the guiding 'wing' a bit more slender.

... ...After printing the piece I have realized that PETF tube guide was obstructing access to the crews. As the holes were the size of screw head, I have also reduced the size of that holes down to 4,1 mm, so now the guide can be bolted to the extruder.

Upon reviewing the piece, I noticed that PETF tube guide was blocking access for the crew. Since the holes were just large enough to fit a screw head, I decided to shrink them down to 4.1 mm in size. ...This modification allows the guide to be securely...

... ..... ... I moved the opening to the far end of the guide, instead of on the side of it. ... I also extended the feet/arms/tabs of the Attachment, as the original one had the habit of falling off, as it slowly worked its way out of the 2020 extrusion

... which I built upon by incorporating these enhancements. A quarter-inch diameter bolt is used, but any similar-sized bolt with a smooth shank will suffice, provided it covers the area where the filament touches and remains smaller than the hole.

I'm drawn to uncomplicated style. To achieve that look, I took it even further. ... You'll require an adhesive strip or double-sided tape.

All you need is: - 608 bearing ( Inside diameter: 8mm, Outside diameter: 22mm, Thickness: 7mm) - M3x25 screw I used a longer-than-needed screw I had lying around, so don't hate. You have to print the following parts: 1x holder_2 1x holder 1x...

I tailored it specifically to work seamlessly with the Sunhokey Dual Gear Extruder, which can be easily purchased on Amazon.

Recreated in TinkerCAD. ... Print with Supports.

OPDATE Version 2. Made to accommodate bearings of size 608. Features Include: Now accommodates bearings of a specific size, meeting the requirement for 608 bearings. Previous Version (Version 1): Requires two bearings with dimensions of 20 x 9 x...

Fiber Guidance System

The user manually enlarged the bore size of a PTFE tubing section and gave it a slight upward lift.

This remake draws inspiration from the original design found at Thingiverse, specifically thing 2920344. ...A notable alteration is the addition of a second screw hole, as well as the removal of the sliding screw cover.

Utilized with a 22-millimeter bearing.

<p>Original link : <a href="https://www.thingiverse.com/thing:4876137">https://www.thingiverse.com/thing:4876137</a>&nbsp;</p>

my first small proyect

<p>Creator: Jonasen</p><p>https://www.thingiverse.com/thing:2894097</p>

Reimagined in 3D modeling software, TinkerCAD. ...Printed with precision and structural integrity using supports to ensure stability.

Modified End clip to fit around the vertical frame screw and prevent the clip from slipping out.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9SDNMTzZSIx

First, print the roller.stl file directly. Next, proceed to print the bracket.stl file separately. No supports are required in this process. Pause the print when it reaches a height of 22-23 millimeters. ...Once paused, carefully place the roller into...

Ender 3 Pro Filament Guide

Ender 3 Pro Filament Guide