ender 3 filament runout sensor 3d models

This is a rotated version of the [Ender 3 S1 Filament Sensor Mount / Holder V2](https://www.thingiverse.com/thing:5183896)

... ...the filament sensor is too low and the hole for the filament does not line up. This block goes under the filament sensor and raises it to the correct height. ...You will need M3x30mm screws to replace the ones holding the filament sensor from stock.

##Description## Install the excellent BTT Smart Filament Sensor on an Ender 3 v2 quickly and easily, without performing any surgery on the sensor or the printer. There are two mounting options: on top of the frame, or next to the extruder. ...

This is a bracket holding the X axis motor, the X limit switch and the filament run-out sensor for the Creality CR10S, CR10 and the Ender 3. It was made to accommodate a direct drive modification:3 x-limit switch and filament runout mod demo video. ...

This is a subtle remix of franpoli's filament runout switch/guide mod (https://www.thingiverse.com/thing:3743586) for the CR10/Ender 3. The change being the top portion is shifted about 5mm to the left to be flush with the edge of the x-axis motor...

I modified my son's filament sensor mount to be able to mount the Creality filiment sensor on my Ender 3 V2. https://www.thingiverse.com/thing:4890156 His mount corrects alignment issues of other mounts for the Ender 3. ...His uses the repurposed Z...

Filament Sensor mount for Ender 3 with Direct Extruder. It is located on place where stock Ender 3 feeder was located. ...It support PTFE tube mount I use this sensor https://aliexpress.ru/item/33028816768.html from Artillery Sandwinder X1 or Impresora...

A BTT Smart Filament Sensor mount for the Ender 3 Pro. It uses a press-fit mount as well as screw mount to make sure that it fits securely. It was remixed from a mount by anthonyr82. ...His was meant for an Ender 3 v2 with a dual gear extruder and...

Since I wasn't able to find a mount which connects the Advanc3d Filament Sensor to the Ender 3 V2, I designed this simple shape, which fits perfectly. ... Print Time: 18 Min Filament Used: 2g Print Speed: 50mm/s You need 2 M3 screws and nuts to attach...

two trees filament sensor holder for ender 3 there are 2 files, its the same but mirrored (for left/right side of the spool) i recommend to use the left ver for ender users, because it is closer to the board. ... For v slot and sensor use M3 screws.

Filament guide with run-out sensor for Ender 3 PRO when use Aluminum Upgrade Dual Gear Mk8 Extruder. ...Extruder upgrade: https://www.aliexpress.com/item/33041168934.html Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No...

Filament guide with run-out sensor for Ender 3 PRO when use Aluminum Upgrade Dual Gear Mk8 Extruder. ...Extruder upgrade: https://www.aliexpress.com/item/33041168934.html Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No...

... has been modified to be aligned with the entrance of the BMG extruder. If you are interested in the TriangleLab Filament Sensor mount for the stock Ender 3 and Ender 3 Pro please check my other design: https://www.thingiverse.com/thing:4250566

After searching through several versions and remixes using old Z-axis endstops as filament runout sensors, none seemed to match my Ender 3 **PRO**'s endstop perfectly. Now one does exist. I printed it out, installed the endstop, and tested with a...

Made this for my Ender 3 V2 to top mount a Creality filament sensor. I used the original creality M3 screws for the filament sensor and then 2 M4 x 16mm screws for the swivel joint. You need to adjust the tension on the 2 screws so it positions it...

Remixed the "Ender 3 Filament Sensor and guide" by rghawi in order to add some chamfer to the piece so that these sensors (see below for link) would fit. ...Previously, the sensor was so big that the button was pressed with it in the sensor guide (need...

This is an adapter for mounting the filament sensor for the Creality Ender-5 S1 / K1/ Sermoon D3 / CR-200B Pro to the Ender 3 V3 SE printerUse 2 x M3x20 screwsUse connector XH 2.54 3-pin and 4-pinSee the connection diagram in the photo

Wanting to use my eSun eBox Lite filament dryer box with my Ender 3 S1, and looking forward to setting up an enclosure (at some point) in the future, I designed this bracket that allows for fixed placement of the runout sensor with the filament feed...

Wanting to use my eSun eBox Lite filament dryer box with my Ender 3 S1, and looking forward to setting up an enclosure (at some point) in the future, I designed this bracket that allows for fixed placement of the runout sensor with the filament feed...

Ender 3 V2 filament sensor riser for dual gear extruder.I´ve used 4 M3x30mm bolts to fix the riser and the sensor to the mainframe.This was printed in PLA with a layer height of 0,28mm without supports.

Filament Runout Sensor mount comes in different versions Bowden tube PC6 Connector can use the stock sensor from the ELF printer m3 screws needed

Updated: more bulky versionClip to move out filament run out sensor out of middle of the top rail in ender 3 v3 KE.In my case I have filament holder put at left side of my enclosure so I had to move the filament sensor to the left as well.There are...

... the sensor to screw it on. The short PTFE tube will guide the filament beside the Z-rod.See also my reinforced version for the dual gear extruder: https://www.prusaprinters.org/de/prints/104866-smart-filament-sensor-holder-for-ender-3-pro-for-d 

Then run Input Shaping and we're done!EdinBearDragonE3V3 CollectionThis is part of a collection of Ender-3 V3 Mods, designed to fit with the aesthetic of the printer.Ender-3 V3 Top Spool Holder (Rear Facing)Ender-3 V3 Top Filament Sensor...

Ender 3/Pro/V2 Bigtreetech smart filament sensor adapter. After the direct drive update I couldn't find any good solution for the sensor location. This works perfect for me. And don't have to do any changes to the stoke spool holder. Note: Make sure...

***For Creality Ender 3/Pro/V2 Printers Converted to Direct Drive Only*** Converted my Ender 3 V2 to direct drive and needed a place to mount my BigTreeTech (BTT) Smart Filament Sensor. The mounts I found were located in a place that would restrict...

This is a holder for Bigtreetechs Smart Filament Sensor: https://www.bigtree-tech.com/products/bigtreetech-smart-filament-sensor.html I dislike the idea to put it between extruder and hotend on my Ender 3 Pro. Instead I installed it before the...

These two prints allow for the smart filament sensor to be mounted to the top cross piece of an Ender 3 printer and raise the spool holder so it does not interfere with the sensor. This was designed for use with a direct drive modified Ender 3 and...

Created this custom filament guide for users of the Ender 3 3D printer, specifically designed to work seamlessly with the Triangle Labs filament sensor. ...To assemble the guide, you will need to acquire a wheel ring and spacer from the following link:...

This Thing is a Modification/Remix of Tekkins Alu Extruder V1.1 for the Ender 3 V2 I added the platform for the Filament Sensor and removed the Gateway to the Extruder, while i have the linear rail mounted. ... Tekkins Version: ...