ender 3 how to change filament 3d models

Inspired by Greg191134's brilliant snap-on design, this revised guide eliminates friction between the filament and the spool when mounting it on top of the frame, like the Ender 3, thereby preventing problems that often arise. ...Instead, it cleverly...

2.5 Kg Filament Holder for Ender 3. Printed with PLA. Use the standard Filament Holder Hose and put it in the printed Hose. Glue the side Part and the Hose togehter. Put the side Part and the Stand togehter. When needed glue it. ...Have Fun

This is a filament sensor holder for the Ender 3. I used the add-ons holder from thing:3798196 and attached a box which holds the Creality brand filament sensor. The sensor just slides in from the top. The wire reaches if you route the cord...

Top 2020 mount for ender 3 and cr10 printers

It's a roller guide for Creality Ender 3 Neo

a simple filament guide made to fit on an ender 3/pro (any printer with the same size and metal spool holder) without any additional hardware and doesn't interfere with a z axis knob.this style of design is not new, however it is my take on it and...

shortened ukulele neck to fit ender 3

Simple camera holder to Ender 3.

The sensor requires the following hardware to assemble: 1x 5mm Ball Bearing 2x M2 x 6 machine screws 2x the screws that held the switch to the z endstop mount To setup your firmware to allow the use of the switch follow this guide:...

I do think it will fit the other Ender 3's, but I am not sure, be sure to comment if you tried it on any other printer. The holder uses 4x 608 bearings. With this design the spool will unwind gradually. Other spool holders with bearings that i have...

I attached it to my ender 3 w/ direct drive but should work for a bunch of 3d printer configurations I was looking to design something that would follow both the spool and the hot end simultaneously. ... It uses 2 of the common 608ZZ bearings on the...

------------------------------------------------------------------------- Closed box for Ender 3 filament spool. A sachet with desiccant can be placed inside it. Printed with PLA+ and 0.6mm nozzle. Layer height 0.32mm. After placing a desiccant...

... Remix to fit alignment of the Creality Ender 3 v2 extruder. Mount shifted over and down. Sensor tighten tolerance around filament and reduced ball size for 5mm ball. otherwise print roller parts from original. Sensor comes in one piece or split.

This is a remix of ElevationsTech (https://www.thingiverse.com/thing:3950799) filament guide for the Ender 3/Ender 3 Pro. At first the idea of a slot seemed great (you don't need to unload that first roll of filament), but it ended up causing me a...

... ...This filament spool holder uses the stock filament arm and moves it to the top of the Creality Ender 3 enclosure (off of the top of your printer). No additional hardware is required, this uses the same t-nuts and bolts as the stock spool holder.

Reverse bouden filament guide for printing on Ender-3 V3 Se from dryer box (Sunlu-S2).This Thing works on my printer but it is a Work-In-Progress, as I try to enhance some parts.Part for the PTFE fitting designed for M10 threadAdditional parts:PTFE...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

Yes, another filament guide for the Ender 3 is in progress. I'm impressed by the work done by both Filboyt and Holspeed, and I wanted to create a comprehensive guide that incorporates their designs. Here's what you need to print: To complete this...

Once installed you just need to pick the selected GPIO number and input the M600 (filament change) GCODE. Hardware You can use the original M2 screws to hold the plastic part into your printer. To capture the microswitch you'll need two M2x15mm and...

I have made this improvement to the filament support for my Ender 3, which uses the original thread and anchorage to keep the extruder motor from pushing the filament of the coil too forcefully. I modified the size and screw thread to improve its...

Adapter for ICE spool on Ender 3. ... Ø Interior : 30.3mm Ø Exterior : 52.9mm Height : 10mm Don't hesitate to share your makes !

This iteration boasts a 2cm diameter and is specifically designed to be compatible with the original connector found on Ender 3 models.

Helps to fit cheap runout sensor on Ender 3. Mounted on the original X motor axis. Use two M3x22 or longer screws. ... Sensor mount holes distance 20mm.

A top-notch upper filament guide designed specifically for the Creality Ender 3 printer. This innovative design takes into account the standard location of the filament feed on top. This clever guide combines the best features of a long arm snap-on...

This is a quick printing Filament Guide, made to bolt under the stock spool holder for the Ender 3 V3 SE/KE using the stock bolts that came with the printer. Now with Gyroscopic action.Printed with PLA @180mm/s, 0.10mm layer height, w/ wall ordering...

This is a quick printing Filament Guide, made to bolt under the stock spool holder for the Ender 3 V3 SE/KE using the stock bolts that came with the printer. Now with Gyroscopic action.Printed with PLA @180mm/s,  0.10mm layer height, w/ wall ordering...

After upgrading my printer with KevinAkaSam's fantastic belt driven Ender 3 mod, I found I couldn't continue to use the planetary gear filament guide I had been using up until now as it no longer fits where it did. ...Rather than redesigning the support...

With the extra T-nuts provided with my Ender 3 and some M4 x 8mm bolts at my disposal, one of which was more than sufficient in terms of strength, I decided to opt for the snap-fit design instead. ...The open bolt-on version and the open snap-on version...

It secures to the Ender 3 S1 top rail with one M5x12 SHCS and a T-nut. Printed in the orientation shown in the rendering, using PLA with .028 layer height, tree supports, and 20% grid infill, it came out rough on the edges, but at 38 minutes to...