ender 3 laser cutter 3d models

Laser Mount for the Ender 3 that makes it so you can keep your Laser and BLTouch mounted and print as you normally would using the stock hotend shroud.

Support to hold the ender-3 laser and remove it easily. https://youtu.be/1oyUh8zMWbE Try to first put the lower part of the piece under the extruder block. And after, adjust the top of the piece to hear a "clic". I've also installed a "rapid...

Lens cover for Ender 3 laser engraver. You can cover the lens with this cap to avoid dust or debris entering the laser module and to prevent damages from accidental activation of the laser. External diameter of the laser lens adjustment ring:...

My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. ... Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x short...

My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x...

barcket for ender 3 without modifications please if u make it post it :P

Laser Stick to control the laser focus in more safety way. ... I Use and print it on my Ender 3 V2. ... Resolution print of 0.2

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...

This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...

This holds the standard 500mw laser engraver on the Ender 3. It's compatible with BL touch and provides a bit of extra support and stability for mounting the laser. The laser still uses the magnets for attaching to the fan housing, but this mount...

This holder is designed to replace the hotend on the Ender 3 to hold the laser engraver D-B500F instead, which can be purchased here: https://www.creality3dofficial.com/products/creality-blue-violet-light?sca_ref=10788.CFDqhuwn3C The difficulty in...

You will need to print with supports, the current design suits standard Ender 3 V2 and also has a cutout for the mounting screw if you have a fang. (refer to .stl - photo shows V1 with smaller cutout) To use this simply lift the Z Axis to 120mm,...

I got tired of cleaning tape residue off my print bed after using the laser engraver mounted on my Ender 3 Pro. So I designed this handy peg tray system to hold things in place for laser work on top of the print bed. The tray is split in 4 to be...

I made this to mount the official Creality laser cutter/engraver to the front side of the print head. It should work with any 33mm square laser head. This blocks the fan, so you don't want to leave the laser in while doing any 3D printing. The hole...

My laser head mount design for Ender3. ...It can be simply screwed on using the original screws and the laser head can be inserted in. ...

have fun ;) --- Da es keinen Halter für einen Laser gab den man direkt auf die Ender 3 / Ender 5 Hotend Platte schrauben kann, habe ich nun einen erstellt. Den Halter einfach auf den Laser schrauben, Hotend und Lüfter demontieren und den Laser auf...

This is a modified remix of mrfansworth. ...This one is a little wider for my sainsmart laser. ... Removed a few internal layers.

Zum Anbringen der Halterung werden 2 M3 Schrauben benötigt. ...Falls der Laser locker sitzen sollte können die unteren Bohrungen zum fixieren verwendet werden. ... Support wird beim drucken benötigt Infill 20 - 25%

(Will post the pictures in the comments) If the Connection holes of the Backside of your module are the same as the 10W laser it should work just fine. I wanted to keep is as simple as possible. So its designed to replace the hotend (simply hang...

I have my Bltouch on the side, so I had to come up with something I can keep Bltouch, and also have the laser option. This is what I came up with. For some reason, it is upside down. Please print with the flat side touching the build plate for best...

Bracket for OEM Ender3 fan shroud to bolt on common Laser modules from Ebay etc. It sits over the fan shroud and uses a screw and captive nut to tighten it down. ... Use 3x 3mm Screws and 1x 3mm nut (for captive)

Laser headlight module mounting for ender 3.

Creality Ender 3 v2 Laser/BlTouch mount/holder

Mount for Ender 3 V2 laser. ...It requires 4 M3 * 6mm screws.

Converts the hotend for an old, broken ender 3 to accept the sliding part on higher power neje laser modules (30w, 40w), converting it to a laser engraver/cutter that can be used with lightburn without any other modifications. Uses fan pwm to...

This thing has been moved to PrusaPrinters: https://www.prusaprinters.org/prints/123897-bracket-for-ender-3-v2-laser-kit

This is a front clip to support laser on a Creality Ender v2 3D printer with 3 screws. ...Useful if BLtouch is installed.

little switch casing for Ender 3/Pro if you have a laser upgrade on your Ender and want to switch between 3D Print and bzzzzzz 7mm diameter hole for switch no support