ender 3 linear rail y axis 3d models

... ( 4mm might work too.. ) For width 6mm-Black ( black is cool.. ) then print two Screw_-_[_Mk8__-_GT2_20T_+_M4.stl from https://www.thingiverse.com/thing:2854971/files I think that was probably the best upgrade I have ever made for my ender 3 v2.

This is a Remix of My Creality Ender 3 - Y Axis Cover. After struggling to achieve good results with Octolaps and octoprint, I finally succeeded in creating this remix from ActionMed's original design. The new part matches the bearing at the front of...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

I followed A_Make Designs' tutorial on Ender-3 stepper motor dampers with press-fit pulleys, but I realized I couldn't use his printouts or method for spacing the Y axis stepper for the damper. So, I created this one myself. For those who don't know,...

What I changed compared to d30f2n's thing: - Now mounts to y-rail belt screw instead of sliding onto the sides - enabled printing lying down therefore improving the rigidity of the mounting hole itself - removed material around mounting hole to...

So I wanted to upgrade to a larger motor and add a dampener for the y and x-axis on my Ender 3. It turned out the motor was far too big, so when I went to make a whole new bracket, I had an idea: just flip the Y-axis bracket vertically and mount that...

I found the Drag chain/Solid cable chains are a significant improvement over the standard "ender 3 cable chains".Download actual chain files here: https://www.thingiverse.com/thing:371500Installation of these chains is a bit more involved, but well...

Ender 3 Pro Y-Axis Front Cover This is designed for the Ender 3 Pro and will not fit the standard Ender 3. This is my first remix/design on Thingiverse. The original version of this was recommended by several YouTubers and web sites. Kudos to...

Combined HauntedWorkshop's cutaway remix with Janubis' 2.0 mount to minimize loss of printable space on the Y axis and boost strength by adding another pair of mounting screws. Printed and mounted on my Ender 3, it has successfully completed a dozen...

I couldn't find any good adjustable Ender 3 Pro Y-Axis tensioner that was low profile and subtle. So I decided to design my own. The tension is adjustable by turning the bottom M4 bolt (pictured) This one has about 4mm tensioning range and works out...

My favorite thing about this design was how it manages to get an un-occluded view of the workbed in the first 20-or-so layers without interfering with the movement of the Y axis or the print head. Downsides: Since it mounts low, the camera will...

I also remixed Ender 5 X and Y Axis Endstop re-orientation by rmpel and TH3D EZABL Mount with Cable Guide/Strain Relief Bracket by fueledbyboredom. This is a complete set of parts to modify an Ender 5 to linear rails with silent endstops and an...

Replacement for Y axis Tensioner case. Stronger than the Original. ... Updated 4/6/23

A simple attachment designed to clip onto the Y-axis for added functionality.

To adapt this Y stop design, I needed to address a change in the new Ender 3's Y sled configuration - it's now parallel, not offset. With a stepper damper installed, the wheel stops about 3-5mm short of triggering the end stop. Additionally, I...

When I disassembled the case of my Y-axis, I found that the bed plate has additional holes designed specifically for mounting an Ender 3 Pro. So, I decided to modify my printer by placing wheels in these holes and turning a 2040 aluminium profile at...

I was experimenting with ribbed designs as an infill alternative for using less material while yielding better strength. Here the rationale of the original mount: This is a Y-axis motor mount for Ender3 Pro. The stock mount requires an idler pulley,...

Ender 3 y mount with voids for 2 8 mm magnets based on shdwstrk's design. I print it with supports with support interface enabled for a better surface to glue the magnets to. Magnets will probably also work as a press fit. ... Shdwstrk's OG design...

Adjustable y endstop for ender 3 printer (and others). It's a direct replacement for the original bracket using all the original screws. There are two variants - one that can move the endstop forward and one that can move it backward. Each one can...

Wanted to mount my Logitech C270 from the Y-Axis on my Creality Ender 3 Pro. (will not fit Ender 3) There are lots of other c270 mounts out there, but most require removing the factory monitor mount. I wanted to retain that. Or most require screwing...

So I wanted to put on a larger motor and a dampener for the y and x-axis on my Ender 3. Turns out the motor was far too big and when I went to make a whole new bracket I had an idea: just flip the Y-axis bracket vertically and mount that way. The new...

I made the model to adapt it to the ender 3 v1. ...it is part of the Lamborghini Ender 3 pro pack

tensioner for X and Y axes of ender 3 printers and the like diameter for 4mm profile screws diameter for 4mm pulley screw joints of the pieces with 3mm screws tension bolt diameter 5mm - V2 pulley bracket: The pulley bracket bore has been corrected...

I'm printing an Ender 3 y mount with voids for two 8 mm magnets based on Shdwstrk's ingenious design. To ensure a strong bond between the magnets and the mount, I'm printing it with supports enabled, allowing me to create a smooth surface for gluing...

... before the home/limit switch triggered. To address this issue, I created a modified mount that shifts the switch forward by approximately 10mm, providing more clearance for the switch to activate before the bed crashes into the y-axis stepper.

It's a remix of Y tensioner for the Ender 3 Pro with 40x40 V-sot Profile. I want to thank Cornely_Cool as he generously shared step files with me. That helped me to adapt his work for wide 10mm idler pulleys. I used W10T20B5 idler pulley. It fits...

... back (motor side) of the Y axis assembly. ...Employs standard F688ZZ bearings sourced from the front y-axis idler (replacing with F608 provides the necessary bend radius for the belt and clearance on that end), a solitary >16mm M3 screw, and an M3 nut.

Modification for adding linear rail on the x-axis on an Ender 5 Plus. Printed in tool steel, optimised for low weight. The parts will absolutely not be stiff enough if printed in plastic. The brackets needs to be printed in two sets, and bearing...

... for stability, after all. Please let me know your results, and whether they helped! I am building my Ender 3 to be 1000mm tall on Z, so with the floppy 2040 Y extrusion that comes stock on the STANDARD Ender, this has made all the difference for me.