ender 3 part cooling fan upgrade 3d models

Minor refinements This is a mod to replace the OEM part cooling fan for a 4020 fan & ABL sensor It involves cutting away a small section of the OEM hot end housing sheet metal (cut area shown in pic) however it is reversible should you want to go...

If you destroyed the whole Fan and don´t want to pay, here is a whole replacement. ...Is probably not fitting right away, because i managed to destroy, besides my whole fan, my motor too and therefore stopped designing

remix of a PrusaPrinters file: https://www.prusaprinters.org/prints/16518-fan-guard-for-prusa-i3-mk3s-snapable

Electronics Enthusiast's Safety Guard. ... Positioned directly beneath the printed circuit board, this protective device safeguards the fan from becoming jammed by stray plastic debris.

Just jussied a few thing up to fit my print head and wanted the extra bolt hole for a 5015 fan

I added some extra flair to the fan's protective covering, giving it a distinctive megalo-box aesthetic that really makes it stand out. ...It was definitely worth the effort.

Minor refinements This is a mod to replace the OEM part cooling fan for a 4020 fan & ABL sensor It involves cutting away a small section of the OEM hot end housing sheet metal (cut area shown in pic) however it is reversible should you want to go...

###Chimera Dual Extruder mount/cooling system 50mm fan version for Tevo Tornado/Creality CR-10/Ender-3 It's a base module that combines a mount and cooling system specifically designed for the e3d chimera dual extruder, compatible with Tevo Tornado,...

Remix of Gabriel3DCaster's CR-10 Fan Mod for Enhanced Airflow. To Optimize Print Quality, Try These Tweaks: - Tilt the duct at a different angle so air hits the nozzle indirectly. ...- Shorten it by 1mm to prevent prints from getting damaged during...

Another Ender3 Fan cover, but who doesn't like variety Best results at 0.2mm Was made using a CAD model and printed in real life without any problems. Possible to print without support but there is a bit of overhand at the top. Without support,...

Remix of Gabriel3DCaster's CR-10 Fan Mod - Airflow Optimization. Change the duct angle so the air won't directly hit the nozzle. 1mm shorter to avoid hit the print when printing. Category: 3D Printer Accessories

... extruder and the new ALU version. ...These extruder components also support iamjonlawrence's Y axis upgrade, while Part E1 from http://www.thingiverse.com/thing:193668 adds a 30mm fan for cooling. ...Stay tuned for a custom bottom plate release soon.

So i was having problems with my cooling, so i went on thingiverse and found a circle vent and one said short and the other said tall. So i printed the short one and after a couple days it melted. ...So i printer the tall one, but it was the same...

Print in elastomer, I use 58D Shore. ... plugs the air duct for part cooling and restricts it by a bit more than 50% I guess WORK IN PROGRESS. ... go crazy!

Remix of https://www.thingiverse.com/thing:1746358I wanted to use the original version together with this Bondtech mount for my HEVO:https://www.thingiverse.com/thing:2768735But I needed to mirror it, so I modified it to be used with a 4010...

The mounting holes of the part cooling fan for Průša i3 printers are quite wide, something about 4.3mm. ...If the mounting screw gets too much torque, it damages the hole and sinks inside.<br>These inlays prevents this.</p><h3>Print...

... setup for the Tronxy X1. I wanted to have a part-cooling fan that doesn't block the view of the hotend, while also allowing good airflow with as few sharp corners as possible. ... I hope you like my version and I welcome any feedback to improve it.

Ender 3 S1 Pro Water Cooling Clips. ... Printing Temperature: 300˚C Bed Temperature: 60˚C Printing Speed: 50mm/s Fan: OFF Direct Drive: Retraction Distance: 3mm Retraction Speed: 40mm/s

Cooling duct for Hemera and Volcano combo on my Ender 3. Mounts to the 'front' end of the Hemera and uses threaded inserts and screws to mount a 40mm fan. ...All M3 screws.

(Might work with some other ones not sure) 4 m5 lock nuts 4 m3 lock nuts 4 m5x12 4 m3x12 8 m3x8 (4 for the sliding block and 4+ for the rail attachment) 4+ m3 t nuts to attach the rail NOTE This upgrade can only be performed on the early ender 3...

... and pushing the screws through to offset the motor slightly before tightening the screws holding it in place. All screws and bolts used were items I had on hand after upgrading the extruder, some of which originated from assembling my Ender 3.

I have upgraded my Ender 3 with direct extruder and hotend got lower for ~10mm. So printers cooling system was cooling hotend, not nozzle area. This tool is also suitable for CR-10 version. ... I have printed it in PLA and was afraid, that it will...

This is a clip on part cooling duct I designed for the Ender 3 Pro. No need to remove or replace any OEM parts, just print it and clip it on. Seeing the wide opening far away from the base of the nozzle I decided to create a duct to direct air...

The duct is fabricated from sturdy materials to provide optimal airflow and support, ensuring that your cooling system operates at peak efficiency. ...By redirecting hot air away from the CPU, this solution helps maintain a stable thermal environment...

Model 1: Part to upgrade our Ender 3 printer to direct extrusion. Only with the printing of this piece, without the need to buy screws, taking advantage of all the original parts of our Ender. if you want to complement the improvement you have the...

This is a bundled STL package to upgrade your Ender 3/Ender 3 Pro/Ender 3 V2 printer to use dual z-axis. All the prints are designed to use as little support as possible, so no material is wasted. This mod requires additional parts such to function...

Remixed (https://www.thingiverse.com/thing:2826255) Version Optimized with Original E3D V6 30mm Hotend Adaptor to Boost Dual 40mm Part Cooling Capabilities. ... This highly compact design is specifically tailored for maximum mobility on a kossel delta...

Hello there, I'm Ender 3 TPU, PLA... Extruder Upgrade - a game-changing upgrade featuring a filament guide and cable holder, taking your 3D printing experience to the next level. I recently put this upgrade to the test using various materials,...

If you're familiar with Ben Levi, the renowned 3D printer constructor and developer from Israel, he's currently working on an Ender-3 Pro Upgrade kit. If you own a regular Ender-3, this corner will enable you to seamlessly integrate the upgrade on...

Remix from AustinAnywhere's EZ Vent; when I use the printer for a long time, the duct bends down due to the heat of the extruder; dragging the piece and taking it off the bed; So I added a little tab that hooks onto the extruder casing and voila,