ender 3 part cooling fan upgrade 3d models

Ender 3 PSU fan cover/silencer. ...Increases the length of path the air has to take and does a decent job of quietening the fan noise.

This is protector for the fan of our Ender 3 printer to prevent the fan from being damaged. ... This product is printed in 1.0 scale.

Shroud for ender 3 fan, it have a test print for core only to make sure it fits snug, in the fan hole.

A custom-made fan shroud is installed on the Ender 3 Motherboard fan, cleverly positioned to minimize noise emanating from the front by reversing its direction.

The E3D Clone hot end mounts a lot lower so the stock part cooling fan ducts blow on the hot end and not at the nozzle. This uses the stock fans and mounting and you replace the existing fan duct. Check the photos for the suggested print...

It employs three 40mm fans, with the two outermost ones linked together to chill the extruded plastic, and the center one focused on cooling the cold side heatsink. The design attaches securely using four M3x10mm screws to the heatsink, while all...

My version of the Ender 3 Power supply fan cover design was created to minimize fan noise, which it accomplishes effectively. The primary objective behind this design is to redirect airflow towards the back, providing an efficient cooling system for...

This was made to replace the part's cooling fan duct for a SV01 to use a Revo Six Prusa hotend. I made this in .2 layer height I would recommend using PETG or something for higher temps since this is meant for an all metal hotend. Maybe even...

A unique aspect of this design is its use of 40mm fans to provide separate cooling for both the heatsink and the part being printed. To accommodate this setup, an effector with a substantial central opening is required; the top ring of the E3Dv6...

...It has space to fit part cooling fans from here: https://www.thingiverse.com/thing:540716. Use washers to secure the part cooling arm to this attachment. When installing on tronxy machines, remove small brass nuts and screw it straight onto a plate.

The updated version (V2) includes an additional printout option for the part cooling blocker mechanism, which I needed to separate from the rest of the design after breaking the original blocker sled during support structure removal. In V2.1, I...

Just got my new Ender 3 and I'm absolutely loving it. Made some key modifications to the stock Fan duct, which significantly improved the results for me. Hope you'll enjoy it just as much too. P.S. Simply rotate it as shown in the print-screen...

Make sure your filament is heat resistant. Normally the air flow would cool the shroud, but if your first layer gets printed without a fan, which is recommended and you need to retry to get a layer to stick, your tool head will be hot and without any...

... Sensor Holder. - The Design is Specifically Optimized for One 30x30x10 Axial Fan to Cool the Hotend and One 30x30x10 Radial Fan for Print/Part Cooling. ...These Fans can be Found on eBay or Amazon and Operate at 5 Volts, Compatible with Duet Boards.

Ender 3 Hotend Fan Fix. Redirects Hotend Fan Airflow Away from Print Object. ...Perfect for Prints with ABS and Other Delicate Materials.

You will need the following parts: +) 2x 50x50x15mm 24V Radial Blowers: https://www.amazon.de/gp/product/B08PV27LVM/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 <-- Hint: If the fans dont work, swicht the polarity from - to + and the other way...

I decided to try to improve the already brilliant part-cooling of onlyDave's system and added in a third outlet pointed at the part from the direction of the fan. This is deliberately smaller than the other two as it's directly in the direction of...

The part cooling system will be situated at the back of the mount. The mount is designed to be directly attached to the carriage plate, with the chimera heatsink positioned in front. ...I'm planning to add an alternative version for a 5015 blower soon,...

Since I had my old but trusty TronXY X5 on my workbench, I found after years of using it as it was delivered, the part cooling assembly could be improved. Originally the blower fan blows all air out of a nozzle directly onto the heater block. Yes,...

Recently upgraded my Ender 3 with an SKR E3 DIP but encountered an issue where the fan collided with the heatsink on the stepper driver, preventing complete closure. To resolve this problem, I designed and installed a spacer that allows for full shut...

This is a model based on Motogeepie's amazing design.&nbsp;(https://www.thingiverse.com/thing:3927320)After trying half a dozen of various ducts I have settled for this.I have been using this duct for the past 2 years and I am very satisfied with its...

This is a replacement cooling fan duct designed specifically for Wombot Drafter 3D printers. It boasts an even broader cooling angle compared to its original counterpart, delivering identical performance results. ...Moreover, it incorporates a sturdy...

And in front of is the chimera heatsink. I will probably add a version for a 5015 blower soon, as the air pressure could be a bit better with this kind of fan(blower) Edit: done: https://www.thingiverse.com/thing:2896701 Let me know what you think!...

I tried several models of ducts I found here on Thingiverse, but it would appear that my part cooling fan has a larger opening than any of the models I found here, because none of them fit. That said, This model that I made from measurements of the...

The stock Fan duct is so bad I needed to design a better one that cooles the material everywhere and not from just one side. So, I designed one. Feel free to modify to your needs. ...A duct for a 40mm fan is planned and will follow.

The front side includes holes for part cooling fan mounting, specifically designed for a Pico hot end. Created using Fusion 3D software, printing requires ABS material with 15% infill, although increasing to 25% is recommended. Support is needed...

this is a simple remix of the Hangtight part cooling fan shroud set up for the Voxelab Aquila. a gentleman names Gene Givens on the official Voxelab FB page created this but only ever loaded it to google drive where the files got lost. files have...

A custom mount combines an E3D v6 hotend, a BLTouch probe, and a 40mm part cooling fan to optimize print quality.\r\n\r\nInspired by previous designs, this creation offers a unique solution for those seeking improved performance.\r\n\r\nNote: This...

I added that file as an option (the differences are moving the mounting hole up 1mm and shaving 1-2mm off the rib in the middle where the fan duct connects to the fan). Note: I use a non-standard nozzle that's a tiny bit taller than the standard...

Get ready to manufacture a superior Nozzle fan duct for your trusty Creality Ender 3 3D printer, and indulge in the satisfaction of a job well done!