ender 3 pi camera 3d models

Ergonomic Axle Camera Mount Designed Specifically for GoPro and Compatible with the Versatile Creality Ender 3 Pro 3D Printer

Remixed from https://www.thingiverse.com/thing:4192636 to place the Pi on its side so as to take up less space. Also removed some of the port holes next to the power cable. ... Re-mixed in TinkerCad.

Remix of [eoyilmaz's LCD enclosure + Raspberry Pi Case](https://www.thingiverse.com/thing:4586351) I wanted to have the raspberry sit at the bottom of the case to allow more space to place items on top of it. Tried to learn FreeCAD to directly edit...

I designed this to keep my Raspberry Pi 4 case tucked out of the way while providing ventilation for the case fan. ...Simply hangs on the lower rails on either side.

IP Camera support for Ender 3 v2 printer. ... I have also attached the OpenSCAD file if you need to fine tune it for your camera

Bracket for mounting a camera to an Ender 3 extruder bracket. ...Part of a project to make a movable camera on a rail.

I had a camera mount that would locate camera to the side of the printing bed. I needed something at the cenet, where i can place my camera, so I made this one. Its a fitst prototype and, i will iterate on it, but your comments are appreciated and...

The video at https://www.youtube.com/watch?v=phYjh2Rwrqk caught my attention, showcasing a simple clip-on design that attaches to the 4040 rail on the bottom left of the printer and features a pivot point to adjust the camera's aim. ...This innovative...

Best to use a 1m cable for your pi camera module v2 if you want a longer arm. I would like to credit the ff since all these designs came from them: https://www.thingiverse.com/thing:4719329 https://www.thingiverse.com/thing:3114849 No need to use...

Needed to mount Pi3 to a decent spot for wifi reception rather than install it in the bottom of the Ender-6 for Klipper/Octoprint. mount holes are 175mm apart and will work on most sides of the Ender-6. Thanks to IMSTRNG for his original design...

I adjusted the number of ports available, also lowered the PI location so that I could add a mount for the fan. I also added posts for a Buck Converter. **Note: I have not printed this yet, and its a work in progress. ...Print at your own risk**

... remix.https://www.thingiverse.com/thing:5455161/remixes.Used the DarkedgeUK version for a while but got tired of it getting knocked around (by me mainly) so I decided to make a fixed version. ...Flipped the bracket and attached the pi cam holder.

... (4 of them for the Pi). -A Pi 3a+ (obviously..) Body and Ring need supports, Lid can be printed without support (as long as you lay flat on the bigger side) I also made small mount for the switch I used to power up this whole thing individualy.

Remixed the Ender 5 End Stop Cover into a Raspberry Pi Camera Case & Mount. I've taken the best elements from various Raspberry Pi Case designs and incorporated them into this one. The result is a ball mount that swivels smoothly. The camera ribbon...

The fan mount is for a 30x30mm fan like the ones that typically come with Raspberry Pi cases is also slightly adjustable to center airflow over the processor or clearance (should it be required) for buck converters. ...(this is why there is a space...

Remixed from: https://www.thingiverse.com/thing:4821226 Front mounted power switch https://www.thingiverse.com/thing:1160062 LM2596 mount https://www.thingiverse.com/thing:4776565 Pi drawer enclosure Supports are only used for the back and right...

... Gehäuse kann innen ein 20mm Lüfter verbaut werden. Der Raspberry Pi wird mit M2,5 * 8mm (selbstschneidend) Schrauben befestigt. Wenn euch der Remix gefällt lasst ein Like da. ...Für Verbesserungs- oder Änderungsvorschläge bin ich immer offen.

RbPi holder for Ender 3Pro/v2 Remixed dual-sided SD slots, and enable screw holes to print without support. ... Compatible with 9cm * 6cm cases like this one in the link below: ...

Frustrated with regular clips slipping off the front rail, I sought a solution to stabilize the camera and ensure it remained level, assuming a well-calibrated machine is essential for accurate results. ... The original arms and mounts can be accessed...

Simple yet effective threaded camera mount designed specifically for use with the Ender 3, positioned at the front left corner of the print bed. Building on the threaded mount and knob concept from https://www.thingiverse.com/thing:3147899, I...

For Raspberry Pi 4B. I couldn't fine one with rails, so I remixed this in Tinkercad with https://www.thingiverse.com/thing:4176051 I had to make the top taller to avoid needing supports, so there is a little gap between the front i/o and the case. ...

To take it to the next level, I drilled a hole into the case to give easy access to the gpio pins on the raspberry pi. This modification should be adaptable to most Creality machines, but confirmation is needed. ...The cap remains unchanged from the...

Here is the link to the original model I remixedhttps://www.thingiverse.com/thing:5248023camera mount Ender 3 S1 raspberry pi camby cabdvr February 15, 2022In my quest for camera mounts I discovered this raspberry Pi camera mount. So I remixed it to...

... bottom component remains unchanged. Changes Implemented: RPI4 camera cable slot has been added RPI4 GPIO pin slot has been integrated Recessed screw holes have been incorporated The fan has been relocated and the screw holes optimized for M3 bolts.

... the airflow holes to the top of the case. - Added hole on the left side for airflow and cable routing. - Added ports for the BTT TFT screen (not tested). - Removed the front side to save filament. - Moved the camera ribbon hole down slightly.

This box works for either Pi 3/3B or Pi 4B (See images) Two part box with overhang latches. Cutouts on the right side for full size HDMI cables and USB-C or Micro USB power. Cutout in back for passing ribbon cable off the LCD screen. Plenty of...

... on @Tronnic's design, one that meets my own set of standards. ...The original lacked a solid foundation, so I reworked it to better fit my vision. I upgraded the display with a 3.5" Waveshare touchscreen and gave the case a makeover to accommodate it.

Raspberry pi camera mount with the use of the flexi arm from here https://www.thingiverse.com/thing:4212206 This is made for my Ender 3 Pro , but i assume it will work on the rest of the Ender 3 series. It clips onto the X-Axis stepper housing, its...

Raspberry pi camera mount with the use of the flexi arm from here https://www.thingiverse.com/thing:4212206 This is made for my Ender 3 Pro , but i assume it will work on the rest of the Ender 3 series. It clips onto the X-Axis stepper housing,...

Here is the spun text: This is a custom-designed attachment for the Ender-3 Bed Handle that allows you to securely position a camera.