ender 3 pro fans 3d models
902075 3d models found related to ender 3 pro fans.thingiverse
Remixed this fan so it would fit my Ender 3 Pro stock fan. Seems to work okay but does have a little more vibration than the stock fan. Only intending to use as a temporary fix until replacement arrives. ...
cults3d
Ender 3 Pro Fan Shroud Scilencer I got extremely fed up with the loud annoying whining that the fan on the hot end of the ender 3 pro makes, so without making the drastic change of swapping out the fan I thought i would come up with something that...
thingiverse
__**Ender 3 Pro Fan Shroud Scilencer**__ I got extremely fed up with the loud annoying whining that the fan on the hot end of the ender 3 pro makes, so without making the drastic change of swapping out the fan I thought i would come up with something...
thingiverse
I remixed this to fit over the Meanwell power supply unit on an Ender 3 Pro. It still has the screw holes but I installed it with double-sided tape straight over the fan inlet to reduce the noise some. PLA, PETG, or ABS could be used. ...It's not...
thingiverse
I like keeping my printer fairly stock. ...So this fan shroud uses the ender 3 mounting points and a 40 mm fan. It does however obscure the print sadly. ...Your call.
thingiverse
Direct Replacement for the original Nozzle 4010 fan cover. ... Fan inlet has a tighter tolerance to reduce blow-by
thingiverse
A hex style cover for each hot end and part fan. ...Need to remove two screws diagonally from the hot end fan, as it snaps into those counter-bores. ... UPDATE: ADDED SQUARED VERSIONS
thingiverse
I decided to design a new fan duct with modifications to ensure enough room between print and fan duct as well as broadened the output to avoid too much air cooling in one spot. In my opinion it produced better printing results. ...You are welcome to...
thingiverse
Remixed from https://www.thingiverse.com/thing:4484483/files. ...Updated to properly fit fan casing and remove errors in .stl file. ... Helps reduce amount of noise.
thingiverse
Cover for Ender 3 Pro Fan with Tool Holder Support only on bed
cults3d
This is a Ender 3 (Pro) fan shroud with an integrated LED (Neopixel) on the bottom side and is compatible with 40x20mm cooling fans - these fans are more efficent and silend. You can put a buck converter into line of it and reduce the speed to about...
thingiverse
This is a Ender 3 (Pro) fan shroud with an integrated LED (Neopixel) on the bottom side and is compatible with 40x20mm cooling fans - these fans are more efficent and silend. You can put a buck converter into line of it and reduce the speed to about...
thingiverse
A simple Ender 3 / Pro fan duct to attach a Noctua 40x40x20mm (Noctua NF-A4x20 FLX) fan instead of the original one. The original part-cooling fan can be attached on the right side. You can use all the original screws. Be careful: The Noctua Fan...
thingiverse
I really liked his design but mounted to Ender 3 pro, the fan mount was a bit loose. This fan duct should fit every Creality printer with the same hot end base plate like the one used for the Ender 3 pro. The back plate is necessary the keep the air...
thingiverse
Very simple remix of the Ender 3 Power Supply Fan Silencer by [Heikomarx] so that it fits the Ender 3 Pro Meanwell power supply.
cults3d
Ender 3's fan noise and additional part to direct the air down. ... It is recommended to use with the ENDER 3 PRO AİR GUİDE BOX.
thingiverse
Projetei este FAN para Ender 3 e Ender 3 PRO para melhor o jato de ar sobre a peça com melhor distrubuição do jato e atingindo a peça num angulo de 25º em todas as direções
myminifactory
There are 2 versions available now the original which fits my ender 3 pro and a shortened one designed to raise the vent up 1.5 MM. I have made mine out of PLA- but recommend ABS or PETG for higher temp printing and times.I have not tested the the...
cults3d
It is designed to to be a direct replacement for the stock Ender 3 Pro vent. It is designed to simulate the effect created by the large "Bullseye" vent yet be easier to make and install. The banshee Version 2 will sit 1.5 mm higher if you need more...
thingiverse
Dies ist eine zweiteilige Version der Satsana Fan , Egal ob MK8 oder Dragonfly. ...PASSt Neues Update
cults3d
Designed for the movie coming out. ...Wanted a Change,not the same boring fan that you find.
prusaprinters
Minimal support required.Best print in ABS or PETG, ABS here with no issues.Need to add a screw and nut, or something like it, to the bottom “front” of the part fan.
thingiverse
I loved the original fan cover however I added some lights to my hot end and wanted to make it a bit bigger to cover up some extra wires a little better. I also thickened the screw hole mounts a little bit so they print a little more friendly. It...
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515 The air Channels would slide after printing the first layer so i made an small connection in between them that can be cutted...
thingiverse
I found this fan duct on Thingiverse ( Ender 3 Pro stock fan ) and it is really looking good, I am pretty sure it is much better than the original part. It fits perfectly to my hot end. Unfortunately one side is sloped and it is difficult to...