ender 3 pro power supply 3d models

ender 3 pro power supply / alimentation

support for positioning the ender 3 pro power supply on the table

Tool holder for Ender 3 Pro power supply. ...Works as is or stick down with 2x tape.

This is for Ender 3 Pro power supply only. Needed Aux power for Raspberry Pi mounted in rear custom case. http://www.thingiverse.com/thing:3688967 Ender 3 all in one, universal rear electronics case by TeachingTech is licensed under the Creative...

Very simple remix of the [Ender 3 Power Supply Fan Silencer](https://www.thingiverse.com/thing:3328495) by [Eigengrow] (https://www.thingiverse.com/Eigengrow/about) so that it fits the Ender 3 Pro Meanwell power supply. I printed off a few layers...

power supply cover for ender 3 pro

Power supply cover for Ender 3 Pro.

Just another fan silencer for the ender 3 pro. Note! ...Never have both screws removed at the same time or the fan will drop into the power supply case.

This is power supply modification for ender 3 pro. ... You need to remove the original cover and replace it by new cover with 80x25 12v fan The frame and the cover mounted by screws from fan.

After printing the power supply holder from kevinakasam's Belt Driven Ender 3 mod, I noticed the gap at the top between the PSU. The Ender 3 Pro has a different PSU than the stock Ender 3, that is not only thinner, but the mount holes are...

Added a second Z Stepper motor to my Ender 3 Pro. Brackets to mount power supply with kit did not fit. Shelf mounts to side and back of leg and is very stable. Power supply drops into shelf and you don't need screws to hold it if you don't want to.

When I upgraded my Ender 3 Pro to dual Z axis, I needed to move the power supply. I did not want to mess with taking it apart or turning it upside down, so I created these options and ultimately chose to mount it in its original location, but...

Since I was going to install a second Z axis kit in the rare 3 pro, I had to change the location of the power supply. However, since the Z axis development parts haven't reached me yet, I prefer the power supply to be shiftable on the profile. This...

This is a holder for the MeanWell LRS 350 power supply that mounts to a 4040 extrusion.After printing the power supply holder from kevinakasam's Belt Driven Ender 3 mod, I noticed the gap at the top between the PSU.The Ender 3 Pro has a different PSU...

I needed mounts for my power supply on my Ender 3 Pro. Easily found a file for the board and screen but couldnt find anything I liked that would allow me to lay it horizontally and space it up for air flow. Shout outs to MrClown for the electronics...

Having recently purchasing a Creality Ender 3 Pro, I loved everything about it apart from the bare power supply bolted to the side if it. I decided to make this in order to clean the visuals up a little. Use double sided tape or foam pads to...

A basic STL. ...for the case I designed on the ender 3 pro. ... Modify it how you please, avoid having to design a perfectly fitting case.

Just a simple decorative cover for the Ender 3 Pro PSU. ... Original model at thangs.com: https://social.thangs.com/m/822959

This mount offsets the power supply a little to the side so you can use dual z lead screw mod (single stepper, belt driven) on your printer You will need: 2 x M4x16 screw 2 x M5x16 screw and M5 nut Print Settings Printer Brand: Creality Printer: ...

... balls, you will need some M4 hardware and T-nuts. Admittedly it has been a long time since I made this modification - I believe you also need to drill 2 small holes in your power supply shroud so you can connect the rear mounts to the shrouds.

This mount offsets the power supply a little to the side so you can use dual z lead screw mod (single stepper, belt driven) on your printer You will need: 2 x M4x16 screw 2 x M5x16 screw and M5 nut

I created this design to fasten the power supply to the outer side of the extruded rails. After upgrading my printer with dual Z motors, the PSU couldn't be attached to the vertical Z supports. I made this design to fit the base of the Meanwell PSU...

Remixed from https://www.thingiverse.com/thing:4568878. ... I added the Ender logo using FreeCad. I think it turned out great. ...Print time with my printer and settings was about 4 h and 15 min.

This is a remix of the "Ender 3 Pro Power Supply Meanwell Baffler" by calaverajoe. ... Scale this to 10% of the original size to fit.

I took the Ender 3 Pro Power Supply Baffler from calaverajoe, but I didn't like how thin it was, so I made it thicker

Adapter for the Ender 3 Pro power supply, to attach a 2-inch duct for ventilation in the case of a closed printer.

Adapter for the Ender 3 Pro power supply, to attach a 2-inch duct for ventilation in the case of a closed printer.

Simple stand for Ender 3 Pro power supply unit (PSU) I detached power supply from the device because of the short plug. However, wire of PSU is under the device, so I made this stand to float wires onto ground. Of course, PSU cable must be...

This is mount is for the Ender 3 Pro power supply to get it away from the Z-Axis. If you are upgrading your printer to Dual Z-Axis this mount is a must have. ... Have Fun and post your Makes =)

This is a housing for the Ender 3 PRO power supply. Two 80mm fans fit into it. The housing already has two integrated fan grids. The lower fan blows in and the upper one out. ... 22.01.2020 EDIT: Added two edited housing: V2: - wall 2mm - 1x...