ender 3 psu control 3d models

i drew this up in autocad 2020 to relocate my control panel on my ender 3 v2. ... requires 4 M3 x 8mm Cap Screws.

Simple and lightweight box for Ender-3 control panel. ...I didn't feel like waiting for a superior model to print out yet.

The original text reads: Ender 3 Left Control Display Holes at the back are 3mm in the 3D model This is just a mirrored control panel of the Ender 3 with some slots for SD cards. Rewritten text: The Ender 3's left control display features...

... is only for the Meanwell PSU from the Pro version, the older PSU is about 50mm width and will not fit! Fits all tools from Ender 3 3 tweezers 6 nozzles The holder for the clipper is the only part which needs support (my support fell over :( )

... nobble's cover to make a fanless cover for the ultimate quiet PSU. ... I've seen similar designs for other PSUs, so decided to make one for the original Ender 3 PSU. ...I have been using this for over 3 months printing non stop, and no issues so far.

A simple L-bracket for hanging the PSU from an Ender 3 v2 underneath the table of a Lack enclosure. I made it thick enough to hold the PSU without too much wobble, but thin enough that you can screw the factory cover back overtop to help camoflage...

The outlet and power switch on the Ender 3 Pro comes out the side and can make it difficult to fit the printer in tight spaces. ... This moves the switch and outlet to the of the psu.

This is MeanWell PSU cover for Creality Ender 3 Pro. This cover is made more rigid and fits my MeanWell better. In the future I'm going to remove fan completely because of fully sufficient passive cooling. ... Enjoy!

I repositioned the PSU on my ender 3 v2 for better cooling so I made this safety cover to cover the dangerous bits. ...The small opening in the cover is for the cables to pass through.

All the mounting hardware that comes with the Ender 3 is designed to be installed right onto the top of the power supply unit, utilizing the screws already in place on the PSU itself.

I created a basic control dial for the Ender 3. ...The main goal was to make adjustments to the recess area where the control switch fits perfectly in place.

Remixed the work of JOulz to fit a Ender 3 Pro Slim PSU I used a Noctua 80x25 mm fan NOTE: Please check if the hole on you psu Line up Befor printing, Its Made for the slim version of the meanwell Powersupply

I'm modifying the Ender 3 Pro with standard Meanwell Power Supply. ... This is a straightforward revision from https://www.thingiverse.com/thing:3426861 - I shifted the screws that attach to the front and back of the PSU two millimeters to the right so...

That's mine version for mounting 120mm fan on Ender 3 PSU. Mounting holes for fan are drawn 2,8mm, you should use M3 screws. If your printer don't handle hole dimmensions you can drill them witm 2,8mm drill. Mounting holes for PSU are not existing....

Remixed nobble's cover to make a fanless cover for the ultimate quiet PSU.I've seen similar designs for other PSUs, so I decided to make one for the original Ender 3 PSU. ...I have been using this for over a year printing pretty often, and no issues so...

Fan shroud assembly to allow the installation of a 80x80x10mm fan on the power supply of a creality ender 3. Installation requires removing the old fan and drilling a few new holes in the metal cover of the psu. ... Wire for the new fan can be run...

To swap out your stock power supply unit (PSU) fan on the Ender 3 pro for a Noctua 60mmx25mm model, you'll need to replace the cover that comes with the printer. The default cover is too thick and won't fit inside the space where the PSU fan sits. I...

I built a custom PSU cover for my Ender-3 v2, tailored specifically to accommodate a massive 92mm fan. This upgrade has drastically reduced noise levels - the PSU is now eerily silent! The fan itself is a Noctua NF-A9x14, a behemoth of airflow that...

A power supply mount for the original Ender 3 that keeps its stock mounting position while still allowing for adjustability and space for a dual-z stepper setup as shown in the images.This is designed for the original wide Ender 3 PSU, not slimmer...

... the height with 5mm compared to the original in order to fit for the Ender 3 V2, which uses a MeanWell LRS-350-24 power supply. ... If you want to prevent the PSU from moving and cover the heads, you can use Ender_3_V2_Mount_-_End_Bracket_Headers.stl

... the height with 5mm compared to the original in order to fit for the Ender 3 V2, which uses a MeanWell LRS-350-24 power supply. ... If you want to prevent the PSU from moving and cover the heads, you can use Ender_3_V2_Mount_-_End_Bracket_Headers.stl

I swapped out the knob on the control panel of my Ender 3 with a miniature hand grenade. Initially, I neglected to insert a safety pin into it. ...You'll find both scenarios captured below for comparison purposes.

To give your Control Knob a major upgrade on our Ender 3 machine is easy. ...No special adhesive is required - this upgraded knob simply snaps into place securely on the original button with a precision fit.

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

I've drawn inspiration from other fanless PSU designs out there, but decided to put my own spin on it by creating one specifically tailored for the iconic Ender 3 PSU. ...After three months of non-stop printing, I'm thrilled to report that this custom...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

A straightforward solution for the Ender 3 Pro's PSU fan cover is at hand. The design redirects airflow towards the rear of the printer, potentially lowering some of the fan noise. I conceptualized this original design as one of my first prints and...

A cover for the Ender 3 Pro PSU fan. Brims are recommended when printing. To install, only have one screw removed at a time, to avoid the fan from falling inside the PSU. Distance between the centers of the screws is around 70mm (60mm fan). EDIT:...

This is a modified version of the tool caddy by SteelTallon, designed specifically to fit snugly over the Ender 3 PSU. The updated design boasts improved support for Neiko Calipers and incorporates a handy holder for a small ruler. Future...