ender 3 s1 octoprint 3d models

Creality Ender 5 S1 enclosure cover created from 4 3D printed support columns and 5 acrylic sheets 2 mm thick. ...Cover is designed to be easily removed and be firmly in place during 3D printing.

Ender S1 Pro Screen replacement camera mount for center stud 1/4-20 stud. Logitech C920 used here. ...Use longer screws and you could mount beside the control pad.

NEW Improved Model Now Available  click this link!11-3-2023 - Fixed PTFE hole. Version 6.1 has the taper taken out and the hole is sized for a better fit and a tubing stop was added.I remixed Valeriy Proklov's model by adding clips so it stays on -...

I liked few designs here, but at the end I wanted something which combines 3 different designs from Thingverse. So that's my variation of mount which has higher angle of view, but also can be mounted at the bottom to look up straight into the nozzle....

Partcooling from 3 sides with evenly distributed airflow. It can be printed with no support as one part. ... Designed for following fans: Noctua NF-A4x20 FLX as a 12 Volt hotend Cooler (needs a buck converter from 24V to 12V) WINSINN 40 mm blower...

... mount. -50,4 x offset -3 y offset DuaL fan V2 released! Separate files now available for download. Sadly, my printer died, so it will take some days until I test this further, but I'll keep on improving it, for sure. ... Keep on making!

Use the spare z-axis microswitch that came with your printer as a remote camera shutter switch. ...adjustable with quick release screws

Design this clip to hold cable from moving and damaging the x-axis cables. I also added an offset to keep it away from the heat of the servo motor. Bracket holds using the nut shown in the picture. ... you can insert the cable and clip it back.

Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT

Just tried to remix it for one 5015 blower fan.

This is a remix with the parts split for better printing. No supports required, unless you want to print everything together. There are 4 files, one for each section and one for the whole thing. I recommend printing them separately to avoid supports...

This keeps your roll in one spot when its narrower than the spool holder, keep the filament exist point centered. ...

I needed to put the scraper somewhere then found a good place.

(In Progress) had to make some slight mods to fit the printer. And I might have to do more mods until it is just right. But here's a few photos of the progress. Any tips or advice would be appreciate. I've added the stls I'm currently using. But I...

My enclosure is at eye-height, so I wanted the LCD to be more upright. ...Mounting it to the extrusion with only one screw didn't work with the upgraded part cooling fan. Material: ASA or PETG for enclosureLayer Height: .20mmInfill: 15%Perimeters:...

requires 2x M3 bolts

I added a Wyze Cam V2 mount point instead of the screw hole in the previous design. This also allows you to tweak the angle of the camera to your liking on the mount since the Wyze Cam can move on its base. The Wyze mount point is not the full...

I used a 24v led strip that I put in an aluminum profile with cover and I added a switch for the command directly connected to the power supply of the machine.the system is fixed by two screws: two threads M5 must be made on the profiles.I am...

Wanted something mounted to the X-axis gantry so the bulky part cooling fan does not block the view of the print. Combined the mount from DrabAlarm with the C270 cover from Pomaser. Camera is oriented right side up so no post processing is needed for...

Just for a better feeling.

<p>When printing from a filament drier the filament can make a sharp angle with the filament sensor (even if threaded through the holes in the spool holder) causing lots of unnecessary friction. This part prevents this from happening.&nbsp;</p><p>Use...

A simple Superman extruder indicator. Found a few online but none that I liked.. So I made my own one! Hope you enjoy it! ... https://youtu.be/qhFPquymN-c

<p>Drawer organiser with place for cutter, USB, 5x SD cards, 5x nozzles and more.</p>

I resized the pockets, added a place for cutters and added a knife slot.

I Designed a bracket to support a ledstrip profile I had laying around. I made it so that it hooks in the upper profile. There is a cutout so a switch can be fitted in the support You can put the cable in the aluminium profile. My led strip is...

i modified https://www.thingiverse.com/thing:5462458 because i use a Neopixel Led strip just like this https://www.adafruit.com/product/1426

This is a remix of the Remixed tool holder by Gixxer"This" This is what i was looking for a tool holder that hold everything I need at a quick of a reach. I love this model had to modify it to hold my magigoo and now I can say its amazing! Holds my...

0,2 layer with 0,4 nozzle! infill idk maybe 10-20 % ! ...Easy Print and glue them together!

I use PLA for all parts. 0.2 Quality20% infilI only used a grip on the base, flap or raft for the pin print, because of the height and to not have to reduce the print speed. ...if your printer 3D is well calibrated, just reduce the speed to go well :)...

斷料檢測器原本的位置距離擠出機較遠，因此無法發揮其應有的作用。為了提高生產安全，我將其移動至擠出機上方，現在更加安心了。如果您方便的話，歡迎來看看新的位置。感謝您的關注。