ender 3 s1 pro bed replacement 3d models
1004858 3d models found related to ender 3 s1 pro bed replacement.thingiverse
This is an Ender 3 S1 Pro bed handle. This design probably doesn't work with other Ender 3 models due to the position of the screws below the bed. !!! DO NOT PRINT THIS ON PLA!!! Or the piece will bend due to the temperature of the heat bed...
cults3d
Simple handle I made for my Creality Ender S1 Pro. Use`s the same screws. ... Feel free to shoot me a like if you like my design ^^
thingiverse
This is a spacer for the Creality hotbed silicone column which allows it to be used on the Ender 3 S1/S1 Pro. Usually the columns are meant for a normal ender 3 which has a cable support which the S1 does not fit, this print allows you to use it...
thingiverse
If it's not too much trouble, I ask that you download my models from printables (https://www.printables.com/model/422895-ender-3-s1s1-pro-locking-bed-level-knob) if you don't intend to "tip the maker" so that I can receive some points towards...
thingiverse
https://www.printables.com/de/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder Prevents cable breakage at the housing outlet and rubbing on the Y-axis motor. It can be attached to the underside of the housing and to the recess for the...
thingiverse
So My S1 Pro hot bed cable fried on me while trying to utilize the entire bed. When the Bed is all the way forward (towards me) the cable that goes into the base housing is super tight and apparently after a few days of printing like this caused one...
thingiverse
Fits confirmed by users (without guarantee): Ender 3 Ender 3 Pro Ender 3 V2 Ender 3 S1 Ender 3 S1 Pro Ender 3 Max Neo Ender 5 Creality CR-10 Voxelab Aquila v2 Update V2: As suggested in the comments by...
thingiverse
Printing Temperature: 300˚C Bed Temperature: 60˚C Printing Speed: 50mm/s Fan: OFF Direct Drive: Retraction Distance: 3mm Retraction Speed: 40mm/s REMIXED FROM: https://www.printables.com/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder...
thingiverse
... area of the bed. More Ender 3 S1 models at https://www.thingiverse.com/vampyrex13/collections/my-ender-3-s1-pro-models. Buy Me a Coffee? ---------------- Do you like my work? ...You can buy me a coffee at https://ko-fi.com/vampyrex13.
thingiverse
This is a Camera Mount for the Ender 3 S1 Pro that clips into the handle of the bed and it works quite well. Print it on its side as is, with supports, and 100% infill as the orientation of the beads will make the clips more flexible and...
thingiverse
Ender 3 S1 Pro Heated Bed Cable Chain. This chain link provides the offset needed from the heated bed to the printer. I used a little bit of Automotive black silicone to adhere the bottom part to the machine. You need to print: 1x...
thingiverse
... ... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it (see pic.) Fully optional. ...
thingiverse
Simple replacement for the original bed handle. Designed it for my IKEA Lack Enclosure because the standard was too long for my purpose. You can use the original screws. ...
thingiverse
I printed this in PETG. ...This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.
cults3d
I printed this in PETG. ...This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.
thingiverse
I loved the minimalist bed handle by schroedaa, but it was a bit too tall and the parts cooling fan was impacting the handle, so I trimmed the handle pull down by 5mm. ...Everything clears fine now and there's still enough handle to pull on.
thingiverse
This is a simple bed handle for the Creality Ender 3 S1 and S1 pro. ...It attaches to the existing threaded holes under the bed with 2 m3 computer motherboard screws.
thingiverse
A remix of the Squat0001's bedlock, which feet better to the Ender 3 S1 I have printed it in PETG (for better resistance than PLA) with supports (didn't tried without supports) Edit 26/05/2023 : I uploaded a V3 with a better Lock capacity
thingiverse
... Installs on the carriage spacers for the y-axis without any hardware required - snaps on. You don't need to remove the bed, and it doesn't affect bed leveling. May work on other Ender 3 models - check fit & spacing first. ... Your mileage may vary
thingiverse
Part description ==================== The spool holder is a replacement part, which reduces the need for vertical space (you can see the difference between the original component and the newly designed version in the picture above). Functionality...
thingiverse
This is a remix from the Ender 3 S1 Pro Tray Insert by turbett1. I wanted to simplify the compartments to not be as limiting. But I also added a few features which I like. ... • Fillets on some bottom edges to help get things out • Holder for...
prusaprinters
I made a one piece model to be printed on a larger printer(like my cr10) but cut it in half so you can print both halves on a standard printer(like me ender 3's). The LED bar on my S1Pro was washing out my streaming webcam and the light shade...
thingiverse
- JST ATTACK - Eurekaled LED CHANNEL WITHOUT ANY MODIFICATION TO THE PRINTER, I MADE A LIGHT FOR THE ENDER 3 S1 PRO. TO BE PRINTED 2 PLA ARMS WITH PRECISE FITTING TO ACCOMMODATE THE ALUMINUM LED TRUNKING. YOU MUST ALSO PRINT 4 ELEMENTS, ALWAYS...
thingiverse
Hi, i have started to create a drawer for the S1 Pro as i couldn't find any yet, this is my first design so be gentle, feel free to make it better as i have no idea about designing these things. My plan is to mount a Pi 3+ within, currently printing...
thingiverse
**Link to download** https://www.printables.com/model/517570-ender-s1-s1-pro-bed-cable-guide This should fix the issue with the heated bed wires from flexing over and rubbing on the motor. Installation notes. 1-remove the screw right under the...
cults3d
Cable guide for the bed of the ender 3, with this mod you can bring the printer closer to the wall without disturbing the cable. Gain space with this mod, very easy to assemble, a support for the bed, another for the base and the chain. ... You use the...