ender 3 s1 pro z axis too high 3d models

This is a Knob that allows you to move the Z Axis very easily. ...It's an exact replica of the Extruder Knob included in the Ender 3 V2, but with the proper thread to fit the TR8 Z Rod.

Ender 3 Z-axis Stabilizer with clip keeps it from sliding down at all times. This stabilizer works perfectly with the z knob found here: https://www.thingiverse.com/thing:3387796, as well as many others. It also pairs seamlessly with the filament...

Rotation indicators for Ender 3 Extruder and Z-Axis Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.1 Infill: 80 Filament: 3RDAX PLA Black Category: 3D Printer Accessories

Tapo C100 camera holder for Ender 3 S1 Pro for corner inserion

I have added a camera mount to the hotbed handle of ender 3 S1 pro printer.

Extra part to hold the filament of Dremel at a Ender 3 S1 pro.

I was getting a bad first layer on my Ender 3 V2 and found my z-axis was jamming slightly, leading to an "elephant foot" effect on my prints. The threaded rod was tilting back along the Y-axis because the motor was too close to the extrusion. This...

Use this model if you have problems with aligning the lead screw. https://www.printables.com/model/635002-ender-3-dual-z-axis-upgrade/ This is a bundled STL package to upgrade your Ender 3/Ender 3 Pro/Ender 3 V2 printer to use dual z-axis. All the...

A remix from "Ender 3 Z-axis Stabilizer" by tumad Modified to hold the z-axis in a lower position to let the upper side of the axis free to fit a knob Version 2 has a hole for a screw to keep it well fixed

Find it here: https://www.thingiverse.com/thing:3741936 Want to move your Ender 3 Pro PSU to accommodate the second Z Motor? Check out this design: https://www.thingiverse.com/thing:3742126 To mount your carriage, you'll need these hardware items: ...

This is a small extension piece for the Ender 3 Z axis knob. Because I have the z extension profiles installed, this knob doesent work anymore. Did you print one and discovered this too, then print this one and glue it to the knob shaft, and you...

A stabilizer for your Ender 3 Z-axis rod, which you can adjust to fit various bearing sizes. ... Installation Insert bearing into printed stabilizer Remove the 4 screws holding the top crossbar Slide the Z-Axis Stabilizer onto the left end of the...

Ender 3 users can achieve precise control over their Z-axis endstops by utilizing an adjustable mechanism that also accommodates M2 bolts measuring 20mm in length. ...This setup enables effortless vertical printing capabilities.

One version has a bearing 608Z, and another does not. ...The guide is for the Z-axis of an Ender 3. ...If you like it, please consider supporting my work through PayPal.

I designed a custom Z-Axis spacer for my Ender 3 printer, which had a severely misaligned Z-axis. To avoid using multiple pre-made spacers and ensure even weight distribution across the entire motor assembly, I decided to create a single unit that...

Z-axis spindle aligner for Ender 3 and similar Mod for Z-axis spindle plumbing. Attached stl files of different screw length. It is recommended to make horizontal expansion test to guarantee the correct screw threading . ... I hope it will be useful...

Remixed By Mythical Now supports Ender 3 V2 Changes to the original - Leaves a small space at the back right of the part for the z axis cable that goes into the motor (see picture) Spaced back so the print is flush with the back of the z axis switch...

This guide just keeps the filament off the Z axis threaded rod. I created a direct drive bracket for the Ender 3 so I don't use this piece anymore, but it served its purpose well. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No...

(2/2/2019) Added a newer version that fits over the Z axis bushing a bit more snug Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Resolution: .12 Infill: 10 Filament: Hatchbox PLA Black Notes: Print with a...

This part it to adapt the official Ender 3 S1 Pro LED Light Bar Kit to work on an Ender 3 / pro / v2. https://www.creality3dofficial.com/products/ender-3s1-led-kit The adapter slips into the top rail and is secured with the outer most bolt that...

During my recent assembly of the Creality Ender-3 kit, I faced the same z-axis misalignment issues that many others have reported. Inserting a shim or spacer behind the z-axis stepper motor does not provide an accurate alignment between the stepper...

Human: Ender 3 Pi Camera z-axis mounting A compact raspberry camera mount has been specifically designed to fit onto the creality Ender 3 pro x-axis gantry. This versatile mount is compatible with all 3D printer builds that feature an aluminum...

I designed my own camera mount for the Ender 3 to attach my logitech camera to the Z axis. This attaches to the X axis motor cover using the default screws so the camera will move up and down as the Z axis changes during printing. ... You will need to...

The only downside of this, is that it requires a couple screws that are not found in common screw sets.Updates:2019-03-26 - Added version that plays well with the Ender 3 ProAlso, check out these other mods that dramatically reduce the sound of your...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

... or made noise when the filament rubbed against them. This guide keeps the filament off the Z axis threaded rod with ease. Created a direct drive bracket for the Ender 3, so no longer use this piece, but it served its purpose well initially.

After finding a lack of Ender 3 S1 Plus upgrades and being a little concerned about all of the free motor wires floating around underneath the bed, I decided to create a cover for the left Z motor wires. ...It should snap around the side of the printer...

This adjustable Z Axis limit switch is engineered to rectify the cumbersome design of the Ender 3 Z Axis. Simply level the bed and swiftly set the limit switch in mere seconds. It's a game-changer, especially when switching between glass, tape, or...

I made the model to fit the ender 3 or pro.