ender 3 s1 pro z offset 3d models

Thanks for letting me know. This centering roller fits directly on the OEM roller on my Ender 3 S1 Pro. No bearings, bolts, etc.I suggest printing the halves vertically as that requires no support. After printing, a small amount of sanding was...

I created this camera mount for the Ender-3 S1 Pro to hold the Arducam camera on the X-axis stepper motor. This one combines parts from 2 different mounts. ... This was created by combining parts from the following: ...

It's designed to incorporate into the original spool holder from the Creality Ender 3 S1 Pro (i don't know if any other creality model as the same spool holder (probably)) Included in the files are the nut and screw, a thread test to know if you have...

This is a Filament Spool Bracket with Bearings for the Ender 3 S1 Pro. I used skateboard bearings that I had on hand. Special attention must be made when slicing the shaft (Cura) because Support must be Blocked for all except the top end of the...

You can find spool holders here, that fit with the Ender 3 S1 Pro. Drill a 8mm hole into the shelf and screw holder and lid together. You have to remove the metal plate at the back of the filament guid. Not sure how it performs for high prints,...

The stepper motor cover for MrPiouPiou's bed cable angle adapter doesn't clear the bed on my Ender 3 S1 Pro - just not enough clearance. This causes the bed cable to catch on the gap in the corner of the stepper motor in the back. To solve the...

So I thought about a light shade for the Ender 3 S1 Pro and searched for it on Thingiverse. But what I found wasn't satisfactory to me. That's why I designed one from scratch. :-) Instead of many others, this design is different in some ways: ...

A Universal camera mount for the Ender 3 S1 Pro (And other models)Simply clips on to the standard bed belt tensioner. It will work either way around, but was designed for use as pictured.</p><p>I've included a few different extension bars so you can...

You will have to scale the part a bit higher if your flow rate is higher to fit the original mount.I uploaded another version (V02) because some users found the fit too tight and there was not enough room for the cable.The component can be printed...

This is an "inverted Bowden" adapter for the Ender 3 S1 Pro. Yeah, I know: what the F is an inverted bowden? So, basically, on a direct drive extruder system, you have a bowden tube running from the spool holder to the inlet of the extruder. This...

I made a thin, sleek, minimal and sturdy vertical PITFT50 V2 display mount for the Ender 3 S1 and S1 Pro without the Raspberry PI in the display casing. My Raspberry is laying behind the printer. You can print the Display_case and the...

Suporte para sensor do eixo Z da Ender 3 PRO. O original trincou com a pressão do parafuso. ...modelei um novo com uma estrutura central reforçando a peça.

Fine adjustment for the z-axis on the Ender 3 pro 3D printer. ...You aill also need a 5x35mm screw and nut.

Sadly the original model doesn't fit with the ender s1 pro, so i made a little remix. There is a hole at the lower end, you can stick a little piece of filament trough, fixing the cable in place. I recommend printing with 100% Infill, the clips...

and I would strongly suggest these to be printed in PETG since PLA variants may warp from heat over time.These are the quantites and parts you will need from @Bananenminister's files : 16-Clips 15-Chain links1- Ground Plate1-Hook (to secure ground...

My June 2022 Creality Ender 3 S1 Pro buzzer is crazy loud, and no other models I found fit. The buzzer noise is now reduced about as much as applying two pieces of 3m vinyl wrap on top of the hole, which I had previously. So, if you have adhesive...

Made a quick holder to attach a small thermometer/hygrometer to the top rail of a Creality Ender 3 S1 Pro. It holds [these thermo/hygrometers from Amazon.](https://www.amazon.com/gp/product/B07GR65CNT). (Incidentally, these things have been working...

Unfortunately I couldn't find a spool holder with load cell that fits to the holder of my 3D printer (Ender 3 S1 Pro). I don't know if this design also works on other printers.I use a HX711 with 12,7x12,7x75 mm load cell (i use the 10kg load cell but...

Route filament from dry boxes to the Creality Ender 3 S1 Pro printer using this [Bowden tube guide](https://www.youtube.com/shorts/nfN7RhlbYGk). The assembly consists of a main control arm, a pulley hook, fitting plate, and snap locks to maintain the...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...

The Ender 3 S1 Pro has a big plastic base that covers up a lot of places where the switch for the 3D Chameleon color changing system could be mounted. I decided to go simple and mount the switch right on the plastic base using 3M Command Strips. So I...

A replacement y-axis stepper mount for the Ender 3 S1 Pro. Tested on my machine which has a gulf coast robotics y-axis rail kit but this is as close as a 1:1 copy of the stock mount as I could get in terms of critical dimensions. It uses the stock...

This is a rack for hosting raspberry pi 4 installed with Octoprint as well as the camera holder.The pi rack is open designed to allow max air flow.For camera holder you will need to print number of arms large/medium/small to suite your need.At least...

Wheel for ender 3 pro z axis rod, allowing movement of z axis by twisting wheel. ...After downloading the file, rotate the part to the orientation easiest for printing.

This thin spacer is one millimeter thick and perfectly matches the Ender-3 Pro's requirements to achieve precise z-axis alignment directly behind the z-stepper motor mount. ...Note that specific needs might differ across various machines.

thirsty_camel made side-entry filament guide for Ender 3 S1, but it had too much of friction when filament was pulled from drybox. I designed these addons to use the original filament guide arm.I used two Wurth 608 2RS bearings. All things is made so...

For the second generation of my squash ball feet design for the Ender 3 S1 Pro, I decided to make 4 variations of the original model starting from scratch!The original model was rigid, simple, and effective; however, had shortcomings in the design...

Since my Ender 3 s1 pro has a filament spool rack with bearings in it i made this end-cap and spool spacer set to allow the spool to use the bearings instead of freely spin. You will need 2 spacers and 1 end-cap, Edit: complete re-write of...

Recipients of this instruction assume all risks associated with its implementation and release me from any responsibility for consequences thereof.Part ListPrinted Parts1x Creality Ender 3 S1 Pro Drawer1x Camera Case1x Cable Cover1x Camera...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, no need for extra hardware ;-) enjoy Print: 0.2 height 4-6 walls 40% infill support: YES Position on bed: As shown on a picture Offset bracket for PSU https://www.thingiverse.com/thing:4610070 Z...