ender 3 s1 pro z offset 3d models

hi. this is a remix from a difrent model i found. still in testing tho! ... still some things to fix.

Basic Corner mount for front corner with one connector only. ... With hole on top: 10mmx10mm, 12 mm deep Stick an arbritrary connector with tube with that dimensions into it.

I already printed a tray insert for my printer (https://www.thingiverse.com/thing:5393379), so I wanted something that would hold the included putty knife and a couple of glue sticks. These won't fit in any tray insets and I didn't want to cut the...

A little twinkercad to make this great design from jsdeprey to be more safe. The length is shorter by almost 4cm to prevent damage to X axis stopper wire underneath. ... You can print the housing of the pi camera from the original project.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hD2zFtkfcQc

requires 2x M3 bolts

Quick and easy access to most commonly used tools

A handy guide that mounts on the filament spool hook to gudie the cabel from a drier box. Make two copies and glue together with cyano acrylate. ...To install you need to remove the cap from the end of the spool holder, slide on the guide and then...

This is a remix with the parts split for better printing. No supports required, unless you want to print everything together. There are 4 files, one for each section and one for the whole thing. I recommend printing them separately to avoid supports...

A box that recieve filament in the begin of your print instead of a line.

Because I do not have a sonic pad or something like that, I use a Xiaomi Mi Home Security Camera with a Magnetic Mount and a Xiaomi Smart Power Plug to control my printer. I remixed Drabalarm's mount so it fit's my securitycamera... ...

A re-design of the original because for some reason mine broke and had a crack in it. Fits perfectly onto the fan using original allen key bolts. ...The original had a 21x3mm aperture, the remake has a 15x2mm aperture giving more of a focus column of...

A collection of extruder spinners to visualize extrusion and retraction. You will need to buy some 4mm dia x 3mm thick magnets for these spinners to work. They press fit into the center hole with a bit of force. I find putting the spinner...

Got worried on how hot the stepper motors were running using a Sonic pad- so hot you couldn't touch them. Uses a single 2280 NVME cooler cut in two (30/40mm) and stuck to the rear and LHS of the motor. Designed this to simply clip over the motor...

Adapterplatte zur optionalen Montage des Lasers an den Montagepunkten des Sprite-Druckkopf. ... Adapter to mount the laser at the same points as the printhead.

This is a remix of https://www.thingiverse.com/thing:5428547. I wanted something a bit less bulky so made this. Best way to attach is to loosen the LED bar with the hex bolt next to the switch and then bend the print open a bit and slide it over...

<p>The overall fit of this piece was just slightly tighter than standard Lego. You can use an unimportant minifig to pop on and off a few times to help with fitting if needed.&nbsp;</p><p>There are small bridges, but supports are not needed. ...I...

JUST FOR FUN

<p>Printed it in vertical position, using tree supports with brim.</p>

Infill 80% Support Checked

This fits the gantry extrusion groves. It is a tight fit. ...I hit it with a heat gun and pushed it in

Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT

I resized the pockets, added a place for cutters and added a knife slot.

Support neded

Custom touch screen control panel stand. ...I wanted something bigger than what was already available.

Infill 50-80% Support Checked

I have put the top ring separately to avoid the need for support. You can glue it after. ...The length of this print is shorter than the original holder.

Remix for the Gantry Tool Holder by RonBen (https://www.thingiverse.com/thing:6122185) Modified to store spatule with a gap for the plastic part, replaced some gaps with holder for microSD card reader with type-C adapter. ... Also branded with my...

I used the camera body from codemonkey 1973 and made my own rail mount and arms The mount sits on the x/y rail