ender 3 spool holder upgrade 3d models
1078964 3d models found related to ender 3 spool holder upgrade.thingiverse
... designed to fit 80mm and 100mm spools and to make a more stable place for weird spools (made by UniFast in my case). Also, 200g spools would work on this holder flawlessly. ... Adapters for 80mm/100mm are choosable, you can swap them in few secs.
thingiverse
Just print it, screw it with original plastic nut and insert the M8 threaded rod of desirable length (see pictures). ... For center spool plugs and nut knobs I used my other design: https://www.thingiverse.com/thing:2666787
thingiverse
When printing with the Ender 3, I sometimes encountered the Filament holder nut on the filament side to turn and lock itself down while extruding, leading to much tension on the Extruder stepper motor and even filament skipping. I therefore designed...
thingiverse
Does require 3 standard longboard bearings (22mm OD, 8mm ID, 7mm thickness). Prints in 3 separate parts that can be assembled. Pictures are from one iteration back, where I had to cut apart the plastic to make it fit on the bracket side. This...
prusaprinters
Přemístění držáku filamentu z horní pozice na bok zvýší stabilitu tiskárny a zároveň zlepší navádění filamentu k extruderu.Jako doplněk k tomuto držáku filamentu na boku tiskárny doporučuji nainstalovat i vodítko filamentu, které pomáhá ještě lepšímu...
thingiverse
upgrade spool holder ender 3 use rolling x4 print: 0.2 infil : 25% thickness: 1.2 no support...
cults3d
upgrade spool holder ender 3 use rolling x4 print: 0.2 infiltration: 25%. ... thickness: 1.2 no support ...
thingiverse
This spool holder can be forced into the back end of the stock Creality Ender 3 spool holder so that you can hold two spools for dual extrusion.
thingiverse
An angled bracket with captive nuts to angle the stock Ender 3 spool holder (Or upgrade stock bracket , in the case of mine) out of the way of a direct drive. 2X M5 Nuts requires (4mm think) Its friction fit in the extrusion so fitment is very...
thingiverse
Hello All, this is a modified version of the ender 3 spool holder upgrade made for the Elegoo Neptune 2. It as a slight angled and I added an extension to the bolt on the end to fit the arm that comes with the neptune 2. Take two 608ZZ bearings or...
thingiverse
Another spool holder for Ender 3. ... Fixed on the left front of the Ender 3.
cults3d
Another spool holder for Ender 3. ... Fixed on the left front of the Ender 3.
thingiverse
for ender 3 / pro or any 4040 profile no new hardware other the existing spool holder and t nuts only had to print the 4040 spool holder with sports touching the build plate. Meant for the Ender bender printer upgrade that turns ur ender into a...
thingiverse
Created this holder for D 52 mm. ...spools. Fits on the existing ender 3 spool. For more consistent filament drag. ...
grabcad
this is ender 3 spool holder!you can check the 3d printed image and stl files here, thank you!https://cults3d.com/en/3d-model/tool/ender-3-spool-holder-ji77
thingiverse
This is an adapter for Creality Ender 3 to use spools with diffent diameter on the orginal holder.
thingiverse
Ender 3 spool holder mount / adapter. no additional screws or nuts required. may not work for everyone, depends on the extruded aluminum your printer was made with. ...
thingiverse
... Hi, I made this spool holder for my ender 3, it´s useful! :) If you always use 1kg spool, infill 50% is enough. ... Peace :)
thingiverse
I need a Spool holder for my smaller diameter spools and all the holders on Thingiverse were just too much. ...This is a simple 30mm shaft with a threaded end cap and hex nut to fit Ender 3 stock spool holder arm. ...
thingiverse
This Ender 3 Spool Holder mounts the spool to the front left side of the machine to allow it to fit in smaller enclosures. This spool holder is designed with a slight 5 degree angle so the spool stays in place. Print this in the orientation in the...
thingiverse
Fixed spool holder for the Creality Ender 3. Many filament spools are too large for the stock holder, this part increases the diameter of the stock holder. This model is self supporting and does not need additional support. ...A small circular...
thingiverse
ENDER 3 SPOOL HOLDER Designed to attach to original ender bracket. Intended to help spool rotate freely. My method for getting threaded part to work properly is printing the HEXNUT using -1.75 horizontal expansion. Otherwise the hexnut will just...
thingiverse
I made a remix of https://www.thingiverse.com/thing:3502973 where you can use the original nut from the Ender 3 spool holder. You also need to print 3 pcs of the Spool_Holder_Dowel_V1. Enjoy! ... * This print need support to be 100%*
thingiverse
Fully printable spool holder with bearings for ender 3. In addition there are two adapters (60 & 54 mm) for different spools. Oct. ...2020: added universal spool adapter (from 54 to 60 mm) and modification for shaft's inner nut (nut -> nut-a).
thingiverse
Spool Holder For Creality Ender 3/pro Requires Bearings https://www.amazon.co.uk/gp/product/B07FXZ15DF?ie=UTF8&th=1&linkCode=ll1&tag=coffeemaster-21&linkId=80a107888fe63a43a044b1e63d80adfc&language=en_GB&ref_=as_li_ss_tl
thingiverse
I recently bought a used Ender 3, unfortunately, it doesn't have a spool holder so decided to 3D print my own spool holder after a quick search in Thingiverse i found one made by il_postino but I decided to modify it a bit to print the bolt...