ender 3 support 3d models

Cable support for Ender 3 series, for mounting on the extruder plate after direct drive conversion.The plate that the extruder stepper motor was mounted to prior to the direct drive conversion was unused, and the cable could use some support to avoid...

... to the extruder. ... This custom design was created from scratch but took inspiration from the 'MK8 Extruder Wire Loom Cable Clip For Ender-3' by Namemogan. ...The original model can be found on Thingiverse at https://www.thingiverse.com/thing:3102898

This is a straightforward wire support/holder for an aluminum extruder on the Ender 3. Installation requires no additional screws. ... The knob in the photo can be found here: https://www.thingiverse.com/thing:3176144 The aluminum extruder itself can...

This is a crucial support bracket for the Ender-3's Z axis lead screw. To install it properly, you'll need to attach one screw and one T-nut. Please be aware that your Z axis may collide with this bracket if the machine is raised too high. ...This...

... directly to the X-axis motor and extruder. ...Created from scratch but heavily influenced by the ingenious 'MK8 Extruder Wire Loom Cable Clip For Ender-3' design courtesy of Namemogan on Thingiverse, found at https://www.thingiverse.com/thing:3102898.

(see pictures) This support is compatible with Rocco81-92s Ender 3 Display LCD PCB Cover https://www.thingiverse.com/thing:2858209. I also recommend using these additional items: * Bobnets V-Slot 4040 End Cap...

Remixed the Ender 3 V2 Satsana to include a support on the back that latches onto the stock hot end plate. This remix prints just like the OG with no supports. There are two options: 1. Satsana w Back Support (No Nuts) - This requires 3...

This is a companion to use with [Ender-3 Side Spool Converter Bracket](https://www.thingiverse.com/thing:3303879).

After I installed the direct drive extrude on my ender 3, I rotated my spool holder 90 degrees in order for it to work perfectly with my extruder. The fact that only one screw of the holder was on bothered me. So I just made a support for the spool...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

I had issues aligning the original part on my Ender 3 Pro. To resolve this, I tweaked it by pushing the support further away from the mounting point by 1.65mm. Additionally, I elevated the bearing holder up by 11mm to ensure it's perfectly aligned...

This is a remix from https://www.thingiverse.com/thing:3023240 to fit the Ender 3 Pro/Meanwell power supply which has only one screw at the back. It uses the original screw (if you want to). No supports needed (if printed with 0.2 layer height or...

The stock extruder on the Ender 3 series lacks a convenient way to attach the mesh-wrapped cable bundle that connects to the hot end. To avoid using screws not included in the upgrade kit, I designed this custom part. This design boasts several...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration. They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration.They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto the...

Ender three users now have access to a robust rear support system that provides unparalleled stability and reliability during printing operations.

This remix adapts the original design from https://www.thingiverse.com/thing:3023240 to match the Ender 3 Pro and Meanwell power supply, which features a single screw at its back. It utilizes the existing screw (if desired) for this purpose. No...

Help reduce some swaying of the upright bars on an Ender 3, Pro, v2, X. Only will fit if you have relocated power supply. Slides into upright T-slots and connects to horizontal bar with 2 t-nuts. 170mm tall can be made taller for additional...

This was made in 2018 for the Original Ender 3. It may work for current/newer versions but I can't confirm it.24/05/2018: Updated to v2 which reduces filament by about 25% and print time by about 15%.This will support the Z-motor and align it...

This was made in 2018 for the Original Ender 3. It may work for current/newer versions but I can't confirm it.24/05/2018: Updated to v2 which reduces filament by about 25% and print time by about 15%.This will support the Z-motor and align it...

This is my design for an Ender 3 S1 Led Bar support.The design is inspired by the official led bar accessory but allows you to use any RGB Led strip that fits inside the bar.In particular, for this project, I used a WS2812 led strip that is...

This is a bolt in cable support for the rear of the Ender 3 V2 that provides support for the main cable run to the Z axis uprights/ hot end/extruder and X axis stepper. As standard this is unsupported and rubs against the edge of the frame as the...

Ender 3 V2 lead screw support to move the support onto the vertical 2040 bar from the top 2020 bar. I needed this part as part of a dual z-axis belt tensioner system to accomodate a GT2 pulley, but will work for general lead screw stablization...

This is a simple to install wire support/holder for aluminium extruder on ender 3.It doesn't need extra screw.the knob in the photo: https://www.thingiverse.com/thing:3176144the aluminium extruder:Aliexpress (Red Right) (5$):...

Direct Cable Holder Installation for Ender 3 Requires an M3x8 Screw. A Quick and Easy Solution to Keep Your Cables Organized. ...Watch the Step-by-Step Guide on YouTube.

A modification of the tool holder to be able to mount it on an ender 3 v2. ...The holder is a little longer and the recesses below the control screen a little smaller.

The only problem, for me, was that the Ender 3 arm for the holder was either: - Meant to be attached to the original metal spool arm (via nut) or - Was oriented in a direction that only made sense for a direct drive setup (The CR-10 & Ender 3 arm)...

This is a sleek and versatile light attachment system designed specifically for the Ender 3. To eliminate the hassle of screws, it's completely rail-mounted, allowing for maximum flexibility and ease of use. Feel free to choose any color you like for...

His support worked great for me until I added a EZABL Auto Bed Level to my Ender 3. At that point the cabling was too thick to be able to secure it. Had it not been for that I'd still be using his support. This support is using his design for the...

I crafted a custom BLTouch Mount for my Ender 3 printer, specifically designed to accommodate a shorter Chinese hotend that falls short of the original. My nozzle would never make contact with the bed, even when the BLTouch was retracted and elevated...