ender 3 test 3d models
905273 3d models found related to ender 3 test.thingiverse
Der Testhund vom Ender 3. ... The test dog which came with the Ender 3.
thingiverse
This is not my model. ...This is the official dog model from the Creality Ender-3 SD card. ...This cute design is a unique way to demo your printer and test calibrations.
thingiverse
a copy of propmaster2000_2019's ender 3 test dog with lower poly count
cults3d
a copy of propmaster2000_2019's ender 3 test dog with lower poly count
thingiverse
Ender 3 test for lines at certain levels A 0.88mm 2 width all is needed - Set line width to 0.44 and 2 walls Original printed at 0.12mm layer height 40mm speed for infill, inner walls - 20mm for outer walls
thingiverse
Made both front paws down and added a separate 3D printed Bone to it's mouth (glued).
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hxsjSDYd3p4
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hxsjSDYd3p4
thingiverse
... more. Ender3_Level_Test_v2.gcode: Just prints the test pattern without leveling so you can check if your bed has shifted, or if you want to insert and test with your own auto-leveling code. Edit the "G28" on line 18 to perform auto-leveling. ...
thingiverse
Created my own first layer test which is fast and also uses many other first layer tests.
thingiverse
This is a retraction test measuring 31x6x52. The base is 2mm thick. No skirt, just the starter line that runs fore to aft from Cura. In 10mm increments from the base of the pole, starts at a retraction of 1mm, 2,4,6,7; all at 25 mm/s. Coasting is on...
thingiverse
This could probably work for any 235x235 printer, using PLA or PET-G. Position the detail so that the Hot-End does not hit the holder, for example glas holder the table. ... Square bed leveling calibration have dimension 205x205mm The first...
thingiverse
Customized version of https://www.thingiverse.com/thing:1381839 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1381839
thingiverse
Customized version of https://www.thingiverse.com/thing:1381839 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1381839
thingiverse
single layer height - 0.2mm 21x21cm total Full bed test, scale to fit any bed. ... perfect for manual mesh bed leveling final test print
thingiverse
I remixed original simple retraction test ---> https://www.thingiverse.com/thing:2563909 Mine model take less time to print but works the same. I changed base height and cut some parts to speed up making. One version is short (very quick) and...
thingiverse
Got bored and came up with a crazy ender 3 bridge test...Rules to this challenge: No use of adhesives,tapes,brims,supports,rafts,must be printed with bridge at top! ...Use any filament or profiles of your choice!
thingiverse
Customized version of https://www.thingiverse.com/thing:127588 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=127588
thingiverse
First layer print for your 3D printer.... is it level ? ... This will show you if it is :D The print takes 10 min and should be printed with 0.4 Nozzle and 0.2mm in Layer Height.
thingiverse
Customized version of https://www.thingiverse.com/thing:538624 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=538624
thingiverse
Somewhat smaller than the original design as I found that more useful, as you aren't usually printing on the edges of your print bed. ... (Don't forget the skirts)
thingiverse
single layer height - 0.2mm 2 perimeters - 0.8mm (0.4 nozzle recommended) 21 x 21cm square should print in about 6 minutes time
thingiverse
single layer height - 0.2mm 25 squares - 1.5x1.5cm each 19.5x19.5cm total perfect for manual mesh bed leveling
thingiverse
Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663
prusaprinters
My take on a switching hotend design. I designed this to take two standart creality hotends, a servo (I used:...
thingiverse
I designed this to take two standart creality hotends, a servo (I used:...
thingiverse
I also modified the Elec bed level 5_8 Offset.gcode file so that it works correctly on Ender 3 V1 without any difficulties. Download the file and use it to facilitate the leveling of the bed. Check out the original project on YouTube: Electronic...