ender 3 test dog 3d models
928523 3d models found related to ender 3 test dog.thingiverse
Der Testhund vom Ender 3. ... The test dog which came with the Ender 3.
thingiverse
This is not my model. ...This is the official dog model from the Creality Ender-3 SD card. ...This cute design is a unique way to demo your printer and test calibrations.
cults3d
a copy of propmaster2000_2019's ender 3 test dog with lower poly count
thingiverse
a copy of propmaster2000_2019's ender 3 test dog with lower poly count
thingiverse
Made both front paws down and added a separate 3D printed Bone to it's mouth (glued).
thingiverse
This a remix for the Ender 3 Test Niko Dog This is a Phone Stand The position of the tail is different from original design
thingiverse
Remix of Creality Ender 3 Dog, removed base from the original file in meshmixer and scaled it up in simplify 3d so I could print in different materials and sizes,with out support. ...So far printed in PLA Natural, ABS Grey and Black and Sapphire cheetah...
thingiverse
Ender 3 test for lines at certain levels A 0.88mm 2 width all is needed - Set line width to 0.44 and 2 walls Original printed at 0.12mm layer height 40mm speed for infill, inner walls - 20mm for outer walls
thingiverse
... more. Ender3_Level_Test_v2.gcode: Just prints the test pattern without leveling so you can check if your bed has shifted, or if you want to insert and test with your own auto-leveling code. Edit the "G28" on line 18 to perform auto-leveling. ...
thingiverse
Created my own first layer test which is fast and also uses many other first layer tests.
thingiverse
This is a retraction test measuring 31x6x52. The base is 2mm thick. No skirt, just the starter line that runs fore to aft from Cura. In 10mm increments from the base of the pole, starts at a retraction of 1mm, 2,4,6,7; all at 25 mm/s. Coasting is on...
thingiverse
Someone asked in the comments on the original dog if it could be made into a key fob - and i though that was a great idea, so I made an ender 3 dog dog that can go on your keychain :) NOTE: Scale to 10% of original size to print. Fusion 360 can be a...
thingiverse
Thought the ender dog would look cute with a hat and on my tree so I added a stocking cap and put a hole in one so you can hang it.
thingiverse
Version 1.1, 08/24/2019: Included the Ender 3 test dog. Moved tail to where it would naturally grow. ... Still no idea how to get Thingiverse to show my pictures right...you can see them here: ...
thingiverse
... fine tune at each individual disk. ... helps to run the print a second time just for the skirt to verify additional adjustments done havnt disrupted other corners uploaded because theyre isnt any level tests out there i could find for my ender 3 max
thingiverse
Ender 3 bed level test 1 Print 0.20mm test.stl at 0.20mm layer height with 0.4mm nozzle. 2 After print is done inspect print, see that pla is making good contact with bed. ... 3 Remove from bed measure print height with vernier.(should be 0.2mm) Use...
thingiverse
Il s'agit d'un simple test de 9 points de contact pour régler la hauteur du plateau. ...Fonctionne pour la ender 3 mais il suffit d'adapter la taille dans le slicer pour d'autres imprimantes. ...
thingiverse
This is a version of the bed level test designed for an Ender 3 (215x215mm). This version won't force the Cura slicer to print a dotted line like some others. ... Designed for .16 layer height.
thingiverse
I added a second z-screw to my ender 3 and wanted to test the stability/straightness of the z-axis. 245mm Tall x 10mm diameter. I used "vase" settings for single-layer walls. Skirt only bed adhesion for adhesion test as well. ... using 60mm/s print...
thingiverse
A bed level test sized for the ender 3 bed. Dots are designed to line up approx. with the leveling screws. ...Each dot is large enough to make the leveling and spacing obvious without wasting filament in between the leveling screws.
thingiverse
With this little test you can check and adjust the heatbed leveling of the Ender 3 v1. The settings of the .gcode file are for PLA: 200°C Hotend 50 mm\s printing speed 0.2 layer height There is also an .stl file to adjust the printer...
thingiverse
Ender 3 / PLA+ print bed leveling test. I print using eSun PLA+ and 3D Fillies PLA+. I also run with a stainless steel 0.4mm nozzle. Due to my nozzle and previous warping issues I run with the following settings: Extruder Temp = 235 deg C Bed...
thingiverse
This is a quick bed level test for the Ender 3 or any similar sized printer. Prints a disc in each corner, lines crisscrossing from each corner, and 4 shapes in the middle area of print bed. I printed using my normal settings for PLA and without any...
thingiverse
Stringing test. ...This is challenge any Ender that has not been upgraded to an all metal end like the Swiss, or to the Direct Drive. ...
thingiverse
I created this test for the Creality Ender 3 printer, but as long as your bed is larger than 200x200mm you should be good. Q: How can I tell if my bed is level? A: With this test print, after or during the print look at the bed to see if any...
thingiverse
**New PARAMETRIC version is here:** https://www.thingiverse.com/thing:5354125 **You can customize the bed size there, number of points and more** --- **This model is made only for 235x235 bed (like Ender 3)** **For other sizes check the link above**...
thingiverse
Hello, Try this with my ender 3 profile here : https://www.thingiverse.com/thing:3642806 Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting LIKE LIKE LIKE FOLLOW ME BYE