ender 3 v2 add ons 3d models

Needed a big drawer for the left side of my Ender 3 Pro I printed these dual drawers for the front of my printer: https://www.thingiverse.com/thing:3416444 Then upgraded to the Rear Electronics Case from Teaching Tech:...

A remix of FONSWERKS' 25mm feet for the Ender 3 V2, using T-nuts to fix the feet to the frame rather than printed inserts sliding into the rails. No hassle making sure the rail inserts are printed not too loose or too tight, with Tnuts it just...

... bearings, bolts or any extra part; just print it! I used a layer height of 0.2mm, an infill density of 20%, and tree supports. You'll need to print: * Two roll support for spools - Ender 3 - CLAMP * Four roll support for spools - Ender 3 - ROLL

For anyone interested I have put together a modified Voron StealthBurner fan shroud which is a direct replacement onto the ender 3 series. Modified mounting for ender 3 carriage. Modified body to fit the stock mk8 hotend. It retains bowden feed...

For anyone interested I have put together a modified Voron StealthBurner fan shroud which is a direct replacement onto the ender 3 series. Modified mounting for ender 3 carriage. Modified body to fit the stock mk8 hotend. It retains bowden feed...

Simple Bulb base for very good light over the circuit board. ... I did not want to use led strips since I had 2 bulb holders and a switch lying around. designed to fit over top bar on ends 3 v2 (20mm)

Lze použít i pro tiskárny Ender 3, vzhled jako u tiskáren Průša mini, praktičtější používání.

Ender 3 and 3v2 or others using same motor. ... This is my X-Large version Extruder Motor Knob.

For ender 3 stock remix on https://www.thingiverse.com/thing:3091300 o-----------------------o Nozzle size ------------------ 0.4 mm Layer height ----------------- 0.2 mm Bottom/top layer height --- 0.6 - 0.8 mm Shell thickness -------------- 0.8 -...

... your phone in a landscape position to for example stream the printing process.</p><p>Fits Huawei P9 Lite Mini. ...Should work with Ender 3 too. ...Hole for the tensioner bolt may need some adjustement depending on your setup.Designed with tinkercad.

... near by and hadn't found anything I liked, so started learning how to use Fusion360 and designed this. ...It slides into the rails on the bottom of different Ender 3 models. ...I found it printed best from a corner, with a small raft and supports.

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

************************************************** Tested on my Ender 3 v2, but should work on other Ender models if they use the same t-slot rail design. The extruder part may need to be connected via a different method if on a model that is...

work in progress. ...hot end housing using stock ender 3 v2 mount. hot end cover for this type of ender 3 v2 neo hot end using stock fans from ender 3 v2

I found the original design to be a bit tight in that area for my Ender 3 v2 model, leading to unwanted strain in the base. - Redesigned the primary load path within the base and tried to get rid of as much excess material as possible, resulting...

This Thing is a LED Light holder for the Ender 3 V2 and Ender 5 Petsfang Bullseye Duct Petsfang: https://www.thingiverse.com/thing:2759439 I have mounted a 24 Volt COB LED Strip of 5cm on this Holder You need 2 Screws M2x20 and 2 nuts M2 to mount the...

I designed these supports to enclose my Ender 3 V2 and print ABS without the shield feature, as in one closed printer, once to print this filament we should keep de temperature a little high, to avoid warping, delamination and cracks. In my tests, at...

I upgraded my Ender 3 V2 with a Micro Swiss Bowden Extruder recently. I also had the Filament Sensor Kit from Creality installed. Then I noticed, that the intake of the new Extruder and the outtake of the filament sensor does not match. Therefore I...

I just bought my 1st 3D printer, a Creality Ender 3 v2. I did not like the way the filament was pulled at such a sharp angle into the extruder. So, I designed one that I like using TinkerCAD. It uses a common 608 ball bearing. I included a thumbscrew...

I modified Chris's test to fit the Ender 3 V2. It is designed to work within the 235x235 bed and prints at 220x220 so it stays away from any clips that are used to hold the bed in place. Edit: You may need center the model and then shrink to 99%...

I think the Ender 3 V2 has similar ones. ...Found the file at <a href="https://www.thingiverse.com/thing:4737883">https://www.thingiverse.com/thing:4737883</a>.</p><p>It printed great, but I wanted a slightly tighter fit and I made the slope steeper to...

This is a bolt in cable support for the rear of the Ender 3 V2 that provides support for the main cable run to the Z axis uprights/ hot end/extruder and X axis stepper. As standard this is unsupported and rubs against the edge of the frame as the...

Remix del siguiente carro Satsana para ender 3 v2 https://www.thingiverse.com/thing:4623647 La idea a la hora de hacer este diseño es tener una pieza que se ajuste a la placa del carro modo plug and play, para hacerlo todo mas sencillo a la hora de...

A redesign of the Ender 3 v2 attachment for bed and Z chains by wku_wake. This design utilizes the hardware from the z stop mount after adding a bed level like the BL Touch.</p> <h3>Print Settings</h3> <p><strong>Rafts:</strong></p> <p>No</p> <p...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

We recently installed an Ender 3 V2 in our off-road camper and with space being at a premium, I tried to make it as compact as possible. The X-axis adjustable tension mechanism stuck out much further than I would have liked, and would catch other...

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

Just what we need yet another d__n tool holder to attach to the Ender 3 V2.  I decided I needed my very own tool holder for all the stuff I wanted to have at hand. I made it in lots of bits for a couple of reasons. I hate having to clean supports off...

We recently installed an Ender 3 V2 in our off-road camper and with space being at a premium, I tried to make it as compact as possible. The X-axis adjustable tension mechanism stuck out much further than I would have liked, and would catch other...