ender 3 v2 alternative 3d models
821616 3d models found related to ender 3 v2 alternative.
prusaprinters
27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...
thingiverse
REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...
thingiverse
Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine
thingiverse
Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile
thingiverse
A reimagined version of the `cableChain_Xend` component from johnniewhiskey's [Ender 3 Cable Chain](https://www.thingiverse.com/thing:2920060), featuring an innovative alternative chain connector. This remix is designed to work seamlessly with...
thingiverse
... so desire. This should work on the 3 & 3 pro, but I think the rubber pads aren't as thick. You might need to shave town the top edge or lose the dampening of the stock rubber pads. ... Fusion 360 files included, I don't care if you hack it up.
thingiverse
This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
thingiverse
Top filament sensor all push fit with gap at back for wiring, made from micro roller lever switch KW12-3 and 608zz bearing. See picture for wiring to sensor (pin 1 and 2 on the board) (outer pins for the switch) Top filament cutter with a drawer...
thingiverse
Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports
thingiverse
Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.
thingiverse
Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...
thingiverse
An alternative tabletop mount for ender 3 S1 or S1 pro original spool holder. Can be used with diy enclosure or if you don't otherwise like original spoolholder placement. NOTE: you also need to relocate filament runout sensor. I personally used this...
thingiverse
I've Printed a Few Filament Guides for My Ender 3, but Most Wouldn't Fit Properly. That's Why I Created This Alternative End Clip to Accommodate the Majority of Available Guides. ...It Was Designed in AutoCAD and Printed with Cura, So Hopefully This...
thingiverse
Designed this alternative for zip ties that are used to tie the extruder cable and PTFE Bowden tube. ... It is reusable and snaps right in place without any hassle. Machine used: Creality Ender 3 Print yourself 4 copies in under 10 minutes.
cults3d
reggicavi per piatto ender 3/pro/v2 o simili
thingiverse
Alternative cable support using a tie-wrap is significantly easier to print than before. As this project continues to evolve, it's clear that some adjustments were necessary - in my case, cutting a small corner after printing was required to ensure...
thingiverse
I've modified some aspects of my ender, resulting in a need for an endstop able to hook onto the front with limited space available, so I created this cubed version. ... Required items: M4 x 20mm bolts and M4 T-nuts Easy to mount and adjust.
cults3d
I've Modified My Ender Setup, Requiring an Endstop that Can Hook onto the Front with Limited Space, So I Designed This Compact Version. ... Items Needed: 4 M4 X 20mm Bolts and 4 M4 T-Nuts Easy to Install and Adjust.
thingiverse
This is an altered version of:- "Ender-3_filament_guide_v2.2". By Flint Weiss. FlintWeiss • Seattle, WA I found that when I screwed it down. The brass bearing from the screw interfered with the fitting. And so I added spacers underneath, to...
thingiverse
I recently acquired an Ender 3 V2 drawer and was pleased with its overall design, but noticed one drawback - the spatula didn't fit inside. Given the lack of available solutions to this issue, I decided to take matters into my own hands and create a...